Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Got my paneldue... It says "connecting" and controls nothing...

    Scheduled Pinned Locked Moved Solved
    PanelDue
    10
    49
    6.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • ShawnCundefined
      ShawnC
      last edited by

      The baudrate should be 57600. Try again. I have the same issue earlier.

      1 Reply Last reply Reply Quote 1
      • dc42undefined
        dc42 administrators
        last edited by

        Check that the baud rates on both the PanelDue Setup page and in the M575 P1 command in config.g on the Duet are both set to 57600.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        1 Reply Last reply Reply Quote 1
        • Steve Lynchundefined
          Steve Lynch @Phaedrux
          last edited by

          @phaedrux 1.21.2 (12b1) is what it says.

          Phaedruxundefined 1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @Steve Lynch
            last edited by

            @steve-lynch If you've checked the commands as David says above and it's still not working, you can try flashing the latest firmware. Instructions here: https://miscsolutions.wordpress.com/paneldue/

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • Steve Lynchundefined
              Steve Lynch
              last edited by

              Hello, Thanks for the reply..

              There was not an M575P1 command anywhere in my Config.g Perhaps the Paneldue instruction page should include this?

              The Paneldue instructions make no mention of this anywhere.

              So I searched the M Codes Until I found an explanation.. I set my board using this command: M575 P1 B57600 S1

              I reboot the Paneldue and the Duet.. Still nothing. Just "Connecting"

              Here's my complete Config.G do you see any problems? I've done everything every youtube tutorial, or forum post has suggested.. Thanks so much!

              ; Configuration file for Duet WiFi (firmware version 1.21)
              ; executed by the firmware on start-up
              ;
              ; generated by RepRapFirmware Configuration Tool v2 on Thu Dec 20 2018 18:06:49 GMT-0500 (Eastern Standard Time)

              ; General preferences
              G90 ; Send absolute coordinates...
              M83 ; ...but relative extruder moves
              M575 P1 B57600 S1 ;Set baud rate Duet Board.
              M575 P0 B57600 S1 ;Set baud rate USB
              ; Network
              M550 P"My Printer" ; Set machine name
              M552 S1 ; Enable network

              ;*** Access point is configured manually via M587
              M586 P0 S1 ; Enable HTTP
              M586 P1 S0 ; Disable FTP
              M586 P2 S0 ; Disable Telnet
              M564 H0
              ; Drives
              M569 P0 S0 ; Drive 0 goes forwards
              M569 P1 S1 ; Drive 1 goes backwards
              M569 P2 S0 ; Drive 2 goes forwards
              M569 P3 S0 ; Drive 3 goes forwards
              M569 P4 S0 ; Drive 4 goes forwards
              M584 X0 Y1:4 Z2 E3 ; Apply custom drive mapping
              M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
              M92 X80.00 Y80.00 Z400.00 E415.00 ; Set steps per mm
              M566 X480 Y480 Z12.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min)
              M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; Set maximum speeds (mm/min)
              M201 X1200 Y1200 Z250.00 E250.00 ; Set accelerations (mm/s^2)
              M906 X1200 Y1200 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
              M84 S30 ; Set idle timeout

              ; Axis Limits
              M208 X0 Y0 Z0 S1 ; Set axis minima
              M208 X290 Y290 Z360 S0 ; Set axis maxima

              ; Endstops
              M574 X1 Y1 Z0 S1 ; Set active high endstops

              ; ** BLTouch
              ;
              M307 H3 A-1 C-1 D-1 ; disable heater 3, BLTouch - servo pulse on heater 3 pin (expansion 😎
              M558 P5 X0 Y0 Z1 H5 F200 T5000 ; Type 5 for BLTouch (Normally closed switch on Z-probe inputs)
              G31 X33.00 Y0.39 Z2.74 P5 ; Z=trigger height, P=trigger value, not needed for contact probe, X/Y distance from nozzle
              ;

              ; Heaters
              M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
              M143 H0 S120 ; Set temperature limit for heater 0 to 120C
              M305 P1 B4725 C7.06e-8 R4700 ; Set thermistor + ADC parameters for heater 1
              M143 H1 S280 ; Set temperature limit for heater 1 to 280C

              ; Fans
              M106 P0 I0 S0 F500 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
              M106 P1 F500 I0 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

              ; Tools
              M563 P0 D0 H1 ; Define tool 0
              G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
              G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

              ; Automatic saving after power loss is not enabled

              ; Custom settings are not configured
              G29 S1 ; load stored bed height map

              Phaedruxundefined 1 Reply Last reply Reply Quote 1
              • Phaedruxundefined
                Phaedrux Moderator @Steve Lynch
                last edited by

                @steve-lynch said in Got my paneldue... It says "connecting" and controls nothing...:

                There was not an M575P1 command anywhere in my Config.g Perhaps the Paneldue instruction page should include this?

                I think it's not mentioned because it's already the default.

                Did you try updating the PanelDue firmware?

                What firmware are you running on the Duet?

                Double check the cable continuity and that the pins are going to the right places? It's oftentimes a cabling issue of some sort.

                Otherwise I'm not sure what else to do or check.

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • Steve Lynchundefined
                  Steve Lynch
                  last edited by

                  This post is deleted!
                  1 Reply Last reply Reply Quote 0
                  • Steve Lynchundefined
                    Steve Lynch
                    last edited by

                    This post is deleted!
                    1 Reply Last reply Reply Quote 0
                    • Steve Lynchundefined
                      Steve Lynch
                      last edited by Steve Lynch

                      Firmware on board is updated to 2.02 from 8 days ago.. Paneldue is updated to the latest firmware 1.22.1(28b1) The screen showed the firmware update progress, and said when it was rebooting and all, but it still says "connecting" after re-boot, and no control..

                      Continuity confirmed... It's only 4 conductors.. not hard to keep straight.

                      Hmmmm.

                      1 Reply Last reply Reply Quote 0
                      • Steve Lynchundefined
                        Steve Lynch
                        last edited by

                        Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
                        Firmware Electronics: Duet WiFi 1.02 or later
                        Firmware Version: 2.02(RTOS) (2018-12-24b1)
                        WiFi Server Version: 1.21
                        Web Interface Version: 1.22.6
                        Web Interface by Christian Hammacher
                        Licensed under the terms of the GPL v3

                        1 Reply Last reply Reply Quote 0
                        • Steve Lynchundefined
                          Steve Lynch
                          last edited by

                          Tried it with the ribbon cable interface as well.. it powers it, it shows firmware upgrade status, but it does not "connect".

                          Everyone said "dude, they're more trouble than they're worth"... But I see a lot of folks using them successfully..

                          I'm at a loss here.

                          resamundefined 1 Reply Last reply Reply Quote 0
                          • resamundefined
                            resam
                            last edited by

                            @Steve-Lynch does the PanelDue tell you anything on the console tab?
                            I used to see a few error messages when I set the wrong baud rate...

                            Can you inspect the PCB, and verify that the connection headers are good? Maybe there is a bad solder joint or crack in the PCB? (high-def pictures maybe?)

                            1 Reply Last reply Reply Quote 0
                            • Steve Lynchundefined
                              Steve Lynch
                              last edited by

                              0_1546375287322_2019-01-01 15.38.09.jpg

                              overall
                              view

                              1 Reply Last reply Reply Quote 0
                              • Steve Lynchundefined
                                Steve Lynch
                                last edited by Steve Lynch

                                0_1546375487216_2019-01-01 15.38.20.jpg

                                connector closeup top

                                1 Reply Last reply Reply Quote 0
                                • resamundefined
                                  resam
                                  last edited by

                                  I don't see obvious problems on the PCB - but maybe @dc42 spots something...

                                  If you use the 4-pin connector, try switching the wires of the two data pins (DIN, DOUT).

                                  1 Reply Last reply Reply Quote 0
                                  • Steve Lynchundefined
                                    Steve Lynch
                                    last edited by

                                    I do PCB Repair, and under my scope, there is no break, or bad solder joint... Aside from that, both interfaces do not work.. (ribbon cable, or 4 pin) I have several of each, so it's not the cable, and I have continuity from the solder joint on the duet to the solder joint on the paneldue..

                                    1 Reply Last reply Reply Quote 0
                                    • resamundefined
                                      resam
                                      last edited by

                                      @Steve-Lynch whats the story with the lifted pad / pin in the top left corner, close to RA2/RA7?

                                      Since you seem to be familiar with the topic: do you have a scope? Can you probe the UART pins of the SAM4S directly? just to make sure the traces are all fine.

                                      1 Reply Last reply Reply Quote 0
                                      • Steve Lynchundefined
                                        Steve Lynch
                                        last edited by

                                        That connector, the (X4 connector) was broken off in shipping. While I did email filastruder, I've been told by others that the connector isn't used, so It should not be an issue. The traces leading to the pads are fine, but the pads themselves were ripped off it seems.

                                        I have a Microscope, not oscilloscope.. lol. I replace blown capacitors and power supplies and repair traces and stuff, I'm wasn't trying to be "mr. know it all", I just was establishing that I had checked beyond the obvious...

                                        And I tried swapping din dout, that didn't do anything as expected (rx to rx - Tx to Tx)

                                        resamundefined 1 Reply Last reply Reply Quote 0
                                        • resamundefined
                                          resam @Steve Lynch
                                          last edited by

                                          @steve-lynch said in Got my paneldue... It says "connecting" and controls nothing...:

                                          Tried it with the ribbon cable interface as well.. it powers it, it shows firmware upgrade status, but it does not "connect".

                                          Do you mean it shows a progress bar when you upgrade the DuetWifi firmware?
                                          This would mean the connection DOES work...

                                          1 Reply Last reply Reply Quote 0
                                          • resamundefined
                                            resam @Steve Lynch
                                            last edited by

                                            @steve-lynch said in Got my paneldue... It says "connecting" and controls nothing...:

                                            That connector, the (X4 connector) was broken off in shipping. While I did email filastruder, I've been told by others that the connector isn't used, so It should not be an issue. The traces leading to the pads are fine, but the pads themselves were ripped off it seems.

                                            With all the troubleshooting you have done so far, I would open a warranty claim & ask for a replacement, due to damaged during shipping.

                                            One last thing maybe:
                                            how long are your wires? I suppose you are not trying to run a 10feet long cable...?
                                            Maybe try a really short one / newly crimped just to make sure.

                                            Steve Lynchundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA