Extruder Thermistor in Simplify3D

Gummix

I don't get it.
Extruder is in "Extruder 0" from the Duet
I have created the tool in the following way:

Then I sliced an STL with Simplify:
0_1553350485383_Unbenannöt.png

And if I test it all with the duet then I get the following:

Phaedrux

Can you post the sliced gcode you're trying to print along with your config.g?

Gummix

0_1553372115966_config (1).g
https://www.file-upload.net/download-13547328/MagnetAnstandshalterW-Schrank.gcode.html

I hope they were the right ones, unfortunately I'm not at home anymore to check that out.

Phaedrux

In your config.g it looks like you have no tools defined.

And in your gcode file, it looks like simplify3d is trying to set the temps for tool5, which explains the invalid tool number.

G90
M82
M106 S0
M140 S60
M190 S60
M104 S198 T5
M109 S198 T5
G28 ; home all axes
G92 E0
G1 E-2.0000 F2400
G1 Z0.260 F1002
; process Process1
; layer 1, Z = 0.260
T1
; tool H0.260 W0.342
; skirt
G1 X87.440 Y84.627 F4800
G1 E0.0000 F720
G92 E0
G1 X89.627 Y82.440 E0.1041 F900

https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_definition_section

Gummix

And why is that?
I didn't set anything of a tool 5 in S3D and in Duet I created the tool.

Phaedrux

I'm not sure. I'm not a simplify 3d user. How did you define the tools?

Gummix

Take a look at the pictures, where always "Werkzeug 1" is written you can choose different ones (0-5)
Which sliver do you use?

Phaedrux

It seems you've added the tools from the DWC then? That could be the issue.
From the DWC manual https://duet3d.dozuki.com/Wiki/Duet_Web_Control_Manual#Section_Tools

Tools
Show the configured tools and allows for tools to be added or removed. Currently these additions and removals don't persist through hardware resets so it is recommended to add tools using the M563 G-Code in config.g file as described in Configuring RepRapFirmware for a Cartesian printer.

https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_definition_section

So I would suggest going through that link and adding your tools to config.g so they remain permanently.

I use Slic3r PE and Cura to slice.

Gummix

Hi,
Thanks i will test it.

Gummix

So i added this in the config.g
; Tools
M563 P0 D0 H1 ; tool 0 uses extruder drive 0 and heater 1
G10 P0 S0 R0 X0 Y0 ; set tool 0 temperatures and offsets

Shouldn't this now also be displayed under Tools in the dashboard?
Cause it doesn't show anything.

Phaedrux

This is what I have in my tools section and it does show up in the DWC tools tab.

M563 P0 S"Titan Aero" D0 H1    ; Define tool 0 (Titan Aero extruder)
G10 P0 X0 Y0 Z0   ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
T0    ; Select first tool

Gummix

ok, I had to disconnect the whole power supply to the board (also USB). Then it worked. Thank you