• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

BL Touch Flashing

Scheduled Pinned Locked Moved Solved
Duet Hardware and wiring
4
18
1.3k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    Veti
    last edited by 30 Apr 2019, 14:35

    From the linked document you can see the command to use is M280 with the parameters for your connection and the command to execute.

    Also for M557 you need to define the area of your bed where the probing is allowed.
    this depends on the location of your probe etc.
    You could also use the configurator which calculates these things for you.
    configurator.reprapfirmware.org

    1 Reply Last reply Reply Quote 0
    • undefined
      WILLYD3113
      last edited by 30 Apr 2019, 14:47

      The BL touch is now solid red and will test when It turns on but I cannot get it to deploy or retract.

      1 Reply Last reply Reply Quote 0
      • undefined
        Veti
        last edited by 30 Apr 2019, 14:51

        if you cant get it working by adjusting the grub screw you will have to go in deeper.
        see https://www.youtube.com/watch?v=wq5QmN-MIJA

        1 Reply Last reply Reply Quote 1
        • undefined
          WILLYD3113
          last edited by 30 Apr 2019, 14:51

          New Config:
          ; Configuration file for Duet WiFi (firmware version 1.21)
          ; executed by the firmware on start-up
          ;
          ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 30 2019 09:39:22 GMT-0500 (Central Daylight Time)

          ; General preferences
          G90 ; Send absolute coordinates...
          M83 ; ...but relative extruder moves

          ; Network
          M550 P"PussySlayer" ; Set machine name
          M552 S1 ; Enable network
          M587 S"11818e" P"endless.955.drift" ; Configure access point. You can delete this line once connected
          M586 P0 S1 ; Enable HTTP
          M586 P1 S0 ; Disable FTP
          M586 P2 S0 ; Disable Telnet

          ; Drives
          M569 P0 S0 ; Drive 0 goes backwards
          M569 P1 S1 ; Drive 1 goes forwards
          M569 P2 S0 ; Drive 2 goes backwards
          M569 P3 S1 ; Drive 3 goes forwards
          M350 X256 Y256 Z256 E256 I0 ; Configure microstepping without interpolation
          M92 X1280.00 Y1280.00 Z6400.00 E6790.61 ; Set steps per mm
          M566 X900.00 Y900.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
          M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; Set maximum speeds (mm/min)
          M201 X500.00 Y500.00 Z20.00 E250.00 ; Set accelerations (mm/s^2)
          M906 X1200.00 Y1200.00 Z1200.00 E1600.00 I0 ; Set motor currents (mA) and motor idle factor in per cent
          M84 S30 ; Set idle timeout

          ; Axis Limits
          M208 X0 Y0 Z0 S1 ; Set axis minima
          M208 X220 Y220 Z220 S0 ; Set axis maxima

          ; Endstops
          M574 X1 Y1 Z1 S0 ; Set active low and disabled endstops

          ; Z-Probe
          M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
          M558 P9 H5 F120 T6000 ; Set Z probe type to bltouch and the dive height + speeds
          G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
          M557 X10:210 Y10:210 S25 ; Define mesh grid

          ; Heaters
          M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
          M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
          M143 H0 S120 ; Set temperature limit for heater 0 to 120C
          M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
          M143 H1 S280 ; Set temperature limit for heater 1 to 280C

          ; Fans
          M106 P0 S1 I0 F500 H T10 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
          M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

          ; Tools
          M563 P0 D0 H1 ; Define tool 0
          G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
          G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

          ; Automatic saving after power loss is not enabled

          ; Custom settings
          M307 H3 A-1 C-1 D-1
          M558 P9 H5 F100 T2000
          G31 X0 Y0 Z0 P25

          ; Miscellaneous
          M501 ; Load saved parameters from non-volatile memory

          Deploy probe:
          ; deployprobe.g
          ; called to deploy a physical Z probe
          ;
          ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 30 2019 09:39:22 GMT-0500 (Central Daylight Time)
          M280 P3 S10

          Retract Probe:
          ; retractprobe.g
          ; called to retract a physical Z probe
          ;
          ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 30 2019 09:39:22 GMT-0500 (Central Daylight Time)
          M280 P3 S90

          1 Reply Last reply Reply Quote 0
          • undefined
            WILLYD3113
            last edited by 30 Apr 2019, 17:52

            The interface reads 0 and the BL is solid red(turns off when I pull out the probe) and it does a few test clicks when I turn on the printer but any attempt to deploy or retract goes through the console fine but the BL doesn't do anything.

            1 Reply Last reply Reply Quote 0
            • undefined
              dc42 administrators
              last edited by dc42 30 Apr 2019, 20:12

              @willyd3113 said in BL Touch Flashing:

              Deploy probe:
              ; deployprobe.g
              ; called to deploy a physical Z probe
              ;
              ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 30 2019 09:39:22 GMT-0500 (Central Daylight Time)
              M280 P3 S10
              Retract Probe:
              ; retractprobe.g
              ; called to retract a physical Z probe
              ;
              ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 30 2019 09:39:22 GMT-0500 (Central Daylight Time)
              M280 P3 S90

              See https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Software_setup_Duet_2_WiFi_Ethernet. You need to add the i1 parameter to your M280 commands. Then test M401 and M402 again.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • undefined
                WILLYD3113
                last edited by 1 May 2019, 04:13

                All is working! Thanks Guys!

                1 Reply Last reply Reply Quote 0
                • undefined
                  WILLYD3113
                  last edited by 7 May 2019, 04:17

                  Hey Guys I'm finding a weird issue with the probe. Ive set the probe as my Z Endstop now and I've configured the offset countless times but it doesn't seem to change where the printer thinks zero is. I will set the offset to 0, manually configure where Zero is G92, and run G30 S-1. The printer after restarting then homes when I command it to then goes to z = 5.0 but its really more like 8- 10 and I have no clue why. I've read the BeTrue article and can't figure it out.
                  Here's my Config:
                  ; Configuration file for Duet WiFi (firmware version 1.21)
                  ; executed by the firmware on start-up
                  ;
                  ; generated by RepRapFirmware Configuration Tool v2 on Mon May 06 2019 22:38:59 GMT-0500 (Central Daylight Time)

                  ; General preferences
                  G90 ; Send absolute coordinates...
                  M83 ; ...but relative extruder moves

                  ; Network
                  M550 P"Mods Suck" ; Set machine name
                  M552 S1 ; Enable network
                  M587 S"11818e" P"endless.955.drift" ; Configure access point. You can delete this line once connected
                  M586 P0 S1 ; Enable HTTP
                  M586 P1 S0 ; Disable FTP
                  M586 P2 S0 ; Disable Telnet

                  ; Drives
                  M569 P0 S0 ; Drive 0 goes backwards
                  M569 P1 S1 ; Drive 1 goes forwards
                  M569 P2 S0 ; Drive 2 goes backwards
                  M569 P3 S1 ; Drive 3 goes forwards
                  M350 X256 Y256 Z256 E256 I0 ; Configure microstepping without interpolation
                  M92 X1280.00 Y1280.00 Z6400.00 E6790.61 ; Set steps per mm
                  M566 X1800.00 Y1800.00 Z24.00 E240.00 ; Set maximum instantaneous speed changes (mm/min)
                  M203 X12000.00 Y12000.00 Z360.00 E2400.00 ; Set maximum speeds (mm/min)
                  M201 X1000.00 Y1000.00 Z2040.00 E500.00 ; Set accelerations (mm/s^2)
                  M906 X1200.00 Y1200.00 Z1200.00 E1700.00 I0 ; Set motor currents (mA) and motor idle factor in per cent
                  M84 S30 ; Set idle timeout

                  ; Axis Limits
                  M208 X0 Y0 Z0 S1 ; Set axis minima
                  M208 X220 Y220 Z220 S0 ; Set axis maxima

                  ; Endstops
                  M574 X1 Y1 S0 ; Set active low and disabled endstops

                  ; Z-Probe
                  M574 Z1 S2 ; Set endstops controlled by probe
                  M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
                  M558 P9 H10 F120 T6000 ; Set Z probe type to bltouch and the dive height + speeds
                  G31 P25 X15 Y20 Z3.4 ; Set Z probe trigger value, offset and trigger height
                  M557 X10:200 Y10:200 S30 ; Define mesh grid

                  ; Heaters
                  M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
                  M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
                  M143 H0 S120 ; Set temperature limit for heater 0 to 120C
                  M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
                  M143 H1 S280 ; Set temperature limit for heater 1 to 280C

                  ; Fans
                  M106 P0 S1 I0 F500 H T10 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
                  M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

                  ; Tools
                  M563 P0 D0 H1 ; Define tool 0
                  G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
                  G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

                  ; Automatic saving after power loss is not enabled

                  ; Custom settings
                  M307 H3 A-1 C-1 D-1
                  M558 P9 H5 F100 T2000
                  G31 X0 Y0 Z0 P25

                  ; Miscellaneous
                  M501 ; Load saved parameters from non-volatile memory

                  undefined 1 Reply Last reply 7 May 2019, 07:56 Reply Quote 0
                  • undefined
                    dc42 administrators @WILLYD3113
                    last edited by 7 May 2019, 07:56

                    @willyd3113 said in BL Touch Flashing:

                    Ive set the probe as my Z Endstop now and I've configured the offset countless times but it doesn't seem to change where the printer thinks zero is. I will set the offset to 0, manually configure where Zero is G92, and run G30 S-1. The printer after restarting then homes when I command it to then goes to z = 5.0 but its really more like 8- 10 and I have no clue why

                    G30 S-1 measures the trigger height, but doesn't do anything with it apart form report it. See https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      WILLYD3113
                      last edited by 7 May 2019, 13:27

                      After Probing with G30 S-1 I take that height and plug it into the G31 line of config file, forgot to mention.

                      undefined 1 Reply Last reply 7 May 2019, 16:48 Reply Quote 0
                      • undefined
                        chriskimbr @WILLYD3113
                        last edited by 7 May 2019, 16:48

                        @willyd3113 Ive done this countless times and it doesn't seem to effect where the bed/nozzle is. Mine still prints too far off the bed.

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          WILLYD3113
                          last edited by WILLYD3113 5 Jul 2019, 17:27 7 May 2019, 17:27

                          Is it like 4 to 5 mm away from bed even at z=0? @chriskimbr

                          1 Reply Last reply Reply Quote 0
                          16 out of 18
                          • First post
                            16/18
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA