Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. chriskimbr
    • Profile
    • Following 0
    • Followers 0
    • Topics 20
    • Posts 93
    • Best 1
    • Controversial 0
    • Groups 0

    chriskimbr

    @chriskimbr

    1
    Reputation
    6
    Profile views
    93
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    chriskimbr Unfollow Follow

    Best posts made by chriskimbr

    • RE: Unable to get a quality print with the Duet2wifi yet.

      @deckingman Sorry, will do. I've been troubleshooting trying to figure out the problems and solutions.
      I'll try to do better at what you described.
      I appreciate your guys' help.

      posted in Duet Hardware and wiring
      chriskimbrundefined
      chriskimbr

    Latest posts made by chriskimbr

    • Replaced HotEnd Heater wire and Thermister now faults.

      Duet2wifi v2

      I replaced the Hotend Heater ceramic cartidge wire(same type) and thermistor cartridge wire(same type) and when I attempt to heat the hotend i get this error.

      Error: Heating fault on heater 1 temperature rising much more slowly than expected 1.7C/sec.

      Now Bed won't heat either.

      I also updated firmware to 3.0 then fell back to 2.5 which its currently on.

      posted in Duet Hardware and wiring
      chriskimbrundefined
      chriskimbr
    • Dual Drive Extruder clicking. Extruder speed too high?

      ; Configuration file for Duet WiFi (firmware version 1.21)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v2 on Sat Feb 09 2019 18:37:46 GMT+0000 (GMT)

      ; General preferences
      G90 ; Send absolute coordinates...
      M83 ; ...but relative extruder moves

      M667 S1 ; Select CoreXY mode

      ; Network
      M550 P"TronXY X5SA" ; Set machine name
      M552 S1 ; Enable network
      ;*** Access point is configured manually via M587
      M586 P0 S1 ; Enable/Disable HTTP S0=disable S1=enable
      M586 P1 S1 ; Enable/Disable FTP
      M586 P2 S1 ; Enable/Disable Telnet

      ; Drives
      M569 P0 S0 ; Drive 0 goes backwards
      M569 P1 S0 ; Drive 1 goes backwards
      M569 P2 S0 ; Drive 2 goes backwards
      M569 P3 S1 ; Drive 3 goes backwards
      M671 X421:-111.5 Y162:162 S5 ; leadscrews at mid left, and mid right
      M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
      M92 X80.00 Y80.00 Z100.00 E800 ;E1025 ; Set steps per mm
      M566 X600.00 Y600.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
      ;M203 X9000.00 Y9000.00 Z180.00 E1500.00 ; -origional- Set maximum speeds (mm/min)
      M203 X9000.00 Y9000.00 Z800.00 E400.00 ; Set maximum speeds (mm/min)
      ;M201 X3000.00 Y3000.00 Z250.00 E12000.00 ; Set accelerations (mm/s^2)
      M201 X3000.00 Y3000.00 Z250.00 E400.00
      ;M906 X1250.00 Y1250.00 Z1250.00 E1250.00 I30 ; -origional- Set motor currents (mA) and motor idle factor in per cent
      M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30

      ; Axis Limits
      M208 X0 Y0 Z-1.0 S1 ; Set axis minima
      M208 X330 Y330 Z400 S0 ; Set axis maxima

      ; Endstops
      M574 X1 Y1 S0 ; Set active high endstops
      M574 Z1 S2 ;Define Z to use Probe. Home to Min.
      ;M591 D0 P2 C3 S1 ; Filament sensor on for E0 extruder, simple NO switch connected to E0

      ; Z-Probe
      M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
      M558 P9 H5 F120 T6000 ;last set >H20<, Set Z probe type to bltouch and the dive height + speeds
      G31 P25 X-20 Y-45 Z1.50; Set Z probe trigger value, offset and trigger height
      M557 X30:315 Y15:315 S130 ; Define mesh grid

      ; Heaters
      M305 P0 T100000 B4138 R4700 S"Bed Heater" ; Set thermistor + ADC parameters for heater 0
      M143 H0 S120 ; Set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4725 C7.06e-8 R4700 S"Hot End Heater" ; Set thermistor + ADC parameters for heater 1
      ;M305 P1 T100000 B4138 R4700
      M143 H1 S280 ; Set temperature limit for heater 1 to 280C

      ; Fans
      M106 P0 S0 I0 F500 H-1 ;Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 ; Define tool 0
      G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
      G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

      ; Automatic saving after power loss is not enabled

      ; Custom settings are not configured

      M501 ; read eeprom parameters

      posted in General Discussion
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      @Phaedrux What do you reccomend? Is the 3.0 worth upgrading to?

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      Its up now.

      Not sure what made the difference.

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      @Phaedrux Pinging 192.168.1.47 with 32 bytes of data:
      Reply from 192.168.1.47: bytes=32 time=4ms TTL=255
      Reply from 192.168.1.47: bytes=32 time=4ms TTL=255
      Reply from 192.168.1.47: bytes=32 time=4ms TTL=255
      Reply from 192.168.1.47: bytes=32 time=23ms TTL=255

      From console.

      But chrome or ie i get "This site can’t be reached192.168.1.47 refused to connect."

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      @Phaedrux M503
      ; Configuration file for Duet WiFi (firmware version 1.21)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v2 on Sat Feb 09 2019 18:37:46 GMT+0000 (GMT)

      ; General preferences
      G90 ; Send absolute coordinates...
      M83 ; ...but relative extruder moves

      M667 S1 ; Select CoreXY mode

      ; Network
      M550 P"TronXY X5SA" ; Set machine name
      M552 S1 ; Enable network
      ;*** Access point is configured manually via M587
      M586 P0 S1 ; Enable/Disable HTTP S0=disable S1=enable
      M586 P1 S1 ; Enable/Disable FTP
      M586 P2 S1 ; Enable/Disable Telnet

      ; Drives
      M569 P0 S0 ; Drive 0 goes backwards
      M569 P1 S0 ; Drive 1 goes backwards
      M569 P2 S0 ; Drive 2 goes backwards
      M569 P3 S1 ; Drive 3 goes backwards
      M671 X421:-111.5 Y162:162 S5 ; leadscrews at mid left, and mid right
      M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
      M92 X80.00 Y80.00 Z100.00 E800 ;E1025 ; Set steps per mm
      M566 X600.00 Y600.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
      ;M203 X9000.00 Y9000.00 Z180.00 E1500.00 ; -origional- Set maximum speeds (mm/min)
      M203 X9000.00 Y9000.00 Z800.00 E700.00 ; Set maximum speeds (mm/min)
      ;M201 X3000.00 Y3000.00 Z250.00 E12000.00 ; Set accelerations (mm/s^2)
      M201 X3000.00 Y3000.00 Z250.00 E700.00
      ;M906 X1250.00 Y1250.00 Z1250.00 E1250.00 I30 ; -origional- Set motor currents (mA) and motor idle factor in per cent
      M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30

      ; Axis Limits
      M208 X0 Y0 Z-1.0 S1 ; Set axis minima
      M208 X330 Y330 Z400 S0 ; Set axis maxima

      ; Endstops
      M574 X1 Y1 S0 ; Set active high endstops
      M574 Z1 S2 ;Define Z to use Probe. Home to Min.
      ;M591 D0 P2 C3 S1 ; Filament sensor on for E0 extruder, simple NO switch connected to E0

      ; Z-Probe
      M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
      M558 P9 H5 F120 T6000 ;last set >H20<, Set Z probe type to bltouch and the dive height + speeds
      G31 P25 X-20 Y-45 Z1.50; Set Z probe trigger value, offset and trigger height
      M557 X30:315 Y15:315 S130 ; Define mesh grid

      ; Heaters
      M305 P0 T100000 B4138 R4700 S"Bed Heater" ; Set thermistor + ADC parameters for heater 0
      M143 H0 S120 ; Set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4725 C7.06e-8 R4700 S"Hot End Heater" ; Set thermistor + ADC parameters for heater 1
      ;M305 P1 T100000 B4138 R4700
      M143 H1 S280 ; Set temperature limit for heater 1 to 280C

      ; Fans
      M106 P0 S0 I0 F500 H-1 ;Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 ; Define tool 0
      G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
      G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

      ; Automatic saving after power loss is not enabled

      ; Custom settings are not configured

      M501 ; read eeprom parameters
      ok

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      M115
      FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-01-03b3
      ok

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • RE: Updated Firmware Can't connect to it now

      yes it is

      posted in Firmware installation
      chriskimbrundefined
      chriskimbr
    • Updated Firmware Can't connect to it now

      I have duet 2 wifi v2 with panelduo v2

      I updated the firmware to PanelDue-5.0i-7.0i.bin

      Nothing is working properly now.

      To begin with, it says wifi is connected,
      "WiFi module is connected to access point blablablaname, IP address 192.168.1.47.

      But I cannot connect to it from browser at all.

      posted in Firmware installation wifi module duet 2 wifi
      chriskimbrundefined
      chriskimbr
    • Belt pulleys- changing from 20 tooth to 36 tooth

      axis pulley wheel diameter and teeth count.

      I'm using a h-bot with two of the wheels having teeth. Tronxy x5sa with dust 2 wifi.
      If I switch two of the pulleys wheels with teeth from 20 to bigger diameter 36 teeth do I need to make any configuration seeing changes to accommodate or will it just work?

      posted in Tuning and tweaking
      chriskimbrundefined
      chriskimbr