• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Console/Messages not working

Scheduled Pinned Locked Moved
Duet Hardware and wiring
4
18
1.2k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    Phaedrux Moderator
    last edited by 3 Jun 2019, 14:01

    So you have the panel due reflashed and it powers up again but it still won't connect to your duet?

    And you can't reach the duet through the web interface or over usb?

    What lights are lit on the duet?

    Z-Bot CoreXY Build | Thingiverse Profile

    undefined 1 Reply Last reply 3 Jun 2019, 14:07 Reply Quote 0
    • undefined
      NitroFreak @Phaedrux
      last edited by 3 Jun 2019, 14:07

      @phaedrux
      Yes i reflashed the Paneldue and it does connect to the duet. It is just that when i type some command in the Console/Messages tab and send it, it does not register it and it also does not give me any answer.

      undefined 1 Reply Last reply 3 Jun 2019, 14:23 Reply Quote 0
      • undefined
        Phaedrux Moderator
        last edited by 3 Jun 2019, 14:18

        Try replacing the 4 write cable.

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • undefined
          Phaedrux Moderator
          last edited by 3 Jun 2019, 14:18

          And check the baud rate in the panel due setup screen.

          Z-Bot CoreXY Build | Thingiverse Profile

          1 Reply Last reply Reply Quote 0
          • undefined
            dc42 administrators @NitroFreak
            last edited by 3 Jun 2019, 14:23

            @nitrofreak said in Console/Messages not working:

            @phaedrux
            Yes i reflashed the Paneldue and it does connect to the duet. It is just that when i type some command in the Console/Messages tab and send it, it does not register it and it also does not give me any answer.

            What commands are you sending? Many commands (e.g. G1 commands) don't give rise to any response. So try a command that does, such as M115. Note, if the response is partially obscured by the on-screen keypad, you will need to dismiss the keypad to see the full response.

            Duet WiFi hardware designer and firmware engineer
            Please do not ask me for Duet support via PM or email, use the forum
            http://www.escher3d.com, https://miscsolutions.wordpress.com

            1 Reply Last reply Reply Quote 0
            • undefined
              NitroFreak
              last edited by 3 Jun 2019, 14:45

              I´ve tried connecting it via the ribbon cable and it works the same way as the 4 wire. i can navegate the menus fine, but i cant get a response from the message tab. Its not like I´m new to it, i´ve used it plenty in the past. I´ve tried M112, M115, M997 S0 to reinstall the firmware and then again M115 to see what it did. No response.
              Baud rate is 57600.

              1 Reply Last reply Reply Quote 0
              • undefined
                NitroFreak
                last edited by 3 Jun 2019, 15:00

                When i plug the duet into the computer, it does not do a "ding" that it recognized something and it also does not show up on the COM port list.
                What else can i do to establish contact?

                1 Reply Last reply Reply Quote 0
                • undefined
                  Phaedrux Moderator
                  last edited by 3 Jun 2019, 15:36

                  I fear that the reason your PanelDue is not getting any information from the Duet is because there is something wrong with the Duet. This would explain why you can't also reach it via the web interface. And the fact it doesn't show up as a USB device is also concerning.

                  What LEDs are lit when the Duet is powered?
                  Are there any scorch marks anywhere on the board?

                  You can try going through these fall back procedures 1 2 and 3:
                  https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Fallback_procedure_Num_1

                  Z-Bot CoreXY Build | Thingiverse Profile

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    NitroFreak
                    last edited by 3 Jun 2019, 16:51

                    Okay so the duet works again and I´ve concluded that I´m pretty stupid.
                    Just to be sure, i checked the "How to destroy your Duet" section, and the "Short the endstop supply voltage pin to ground" part caught my eye.
                    When i moved the printer, i noticed that one of the endstops (Y) became unplugged, and i plugged them back in without thinking too much. What do ya think, i connected it in a way that connects the 3.3v to gnd.
                    Connected it the right way and its perfect again, even DWC connects.
                    Did the duet go in some kind of self protection hibernation?

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      Phaedrux Moderator
                      last edited by 3 Jun 2019, 17:21

                      Glad you figured it out.

                      Z-Bot CoreXY Build | Thingiverse Profile

                      1 Reply Last reply Reply Quote 0
                      18 out of 18
                      • First post
                        18/18
                        Last post
                      Unless otherwise noted, all forum content is licensed under CC-BY-SA