Uneven layers

T3P3Tony

Does anyone have any other ideas?
I will try what @deckingman suggested and print a new larger cube without the X and Y imprints to see if the problem remains.

Could this has to do with the 1066.67 steps/mm on the Z steppers?
Would it be better if I geared them down 1:3 to get an even 3200 steps/mm?
Or maybe remove the lead screws and add belts instead?

measure the number of layers in the repeating pattern and then try a different layer height to see what impact it has. Those larger cubes without the X etc indentations make it easier to tie down the problem. It could be because you have non metric lead screws and the later heights don't add up to round numbers but if so this is pretty extreme banding for that.

deckingman

@t3p3tony Tony,

We went through his lead screws and steps per mm etc in his other thread. His screws have a lead of 3mm which is unusual but means that one full step is 0.015mm. So providing he uses layer heights that are multiples of 0.015 then he should be using full steps and not relying on micro-stepping for positional accuracy. So 0.3mm layer height @1066.67 steps per mm @16X would be 320 micro steps or 20 full steps and 0.6mm layer height would equate to 40 full steps.

Even if the firmware rounds 1066.67 up to 1067 steps per mm then 0.3mm becomes 320.1 but you can't have 0.1 of a micro step so it would still send 320 (micro) steps. If the firmware keeps track of the fractional micro steps and adds one on when it gets to a full micro-step, then that would repeat at 3 mm but 1 micro-step is 1/10667 mm so that wouldn't be noticeable.

@Haggan90 Are you sure the lead of the screws is indeed 3mm and not say 1/8 inch? I only ask because 1/8 inch is 3.175 mm which might explain your banding if you set the steps per mm to 3mm. Clutching at straws here..........

T3P3Tony

@deckingman thanks, missed the other thread.

@Haggan90 worth trying the different layer height slices anyway, now you have the cubes printing well and seeing if the repeatability of the issue is the same or different.

Veti

@deckingman said in Uneven layers:

Are you sure the lead of the screws is indeed 3mm

in the link he posted its indeed 3mm lead. however his lead screw is also 800mm long!

can you post a picture of your printer?

deckingman

@veti But did he get what he asked for and ordered? Why is the 800mm length relevant? Mine are 1,000mm.

Veti

at 800mm it would be easy to have one axis offset by a millimetre. that could cause binding of the lead screws.
the ingus nuts are very thight for those lead scews.

Haggan90

This is how it looks right now.

deckingman

@haggan90 If those screws are constrained at the top, try taking the upper mount off. The linear guides should be contstraining any XY movement, not the screws. So if you allow the top of the screws to "float" it will ensure that there are no binding issues.

Haggan90

@deckingman they are Only constraint at the top and not at bottom. I got a flec coupling on the steppers at the bottom.

deckingman

@haggan90 said in Uneven layers:

@deckingman they are Only constraint at the top and not at bottom. I got a flec coupling on the steppers at the bottom.

Those flex couplings might be the cause of your problems, depending on what type they are. If you have any sort of binding on the bearings, some designs of the flex couplings can "wind up" absorbing some of the movement. Then a bit more tension is enough to overcome the binding and you get a sudden jump.

Haggan90

@deckingman That makes sense... because when I attach a precision gauge to the bed and move it down it only moves around 0.001mm-0.003 so it's sturdy. Would any sort of printed couplings work?

Haggan90

@deckingman I just tried to push the couplings together as hard as I could to see if it makes any diffrence, will be back with a photo!

Haggan90

@deckingman Dammit, made no diffrence at all =(

antlestxp

i just upgraded a back up printer I have to a maestro and that printer now shows the same banding. is there a possibility of a firmware issue with coarse threaded z rods. I use fine pitch rods on my primary printer and don't have the issue. or at least it isn't obvious on that printer. they are both hypercubes with the only difference being the pitch of the threaded rods.

this part was printed at .2 in petg with the latest fw
M350 X16 Y16 Z16 E16 I1
M92 X80.00 Y80.00 Z800.00 E407.16

antlestxp

8bit with octoprint vs maestro on the same printer. I will admit 2 different brands of abs and re-sliced to account for the different fw flavor.

Haggan90

@antlestxp looks exactly like my problem!

Haggan90

I tried with a more challanging print and got the same results.

dc42

@antlestxp said in Uneven layers:

8bit with octoprint vs maestro on the same printer. I will admit 2 different brands of abs and re-sliced to account for the different fw flavor.

Did you slice using the exact same layer height in both?
Have you run heater tuning on the bed heater? If you haven't, then it will run in bang-bang mode, which often contributes to layer banding.
Are you using the same Z motor current in both cases?
What stepper drivers does your 8-bit board use? If they don't support stealthChop, or it doesn't use them in stealthChop mode, then it's possible that the default low-speed stealthChop mode of the drivers on the Maestro could be reducing the Z axis precision. So try configuring the Z drivers not to use stealthChop (see the M569 command).

HTH David

Haggan90

@dc42 In my case it's as follow:

Yes exactly the same slicer settings in all cases.
No bed heater installed yet.
N.A
Is this something that I should try? I'm using a Duet Wifi with an Duex2.

Also I just tried with diffrent microstepping and with/without interpolotion. Same results.
Tried with flexible couplings and with stiff couplings on the steppers as well, same result.

I'm comming back to that this could be a firmware or config issue, but I'm out of ideas =/

Veti

what do you mean n/a for question 3?