Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    3DP1000 Duet Ethernet Conversion

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    12
    42
    2.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A Former User?
      A Former User
      last edited by

      @cherno-alpha said in 3DP1000 Duet Ethernet Conversion:

      The Duet Ethernet should be here tomorrow.

      beware if you'll be using the online configurator with power loss function
      https://forum.duet3d.com/post/107325

      Cherno Alphaundefined 1 Reply Last reply Reply Quote 0
      • Cherno Alphaundefined
        Cherno Alpha @A Former User
        last edited by

        @bearer Is this like the Power Resume Feature?
        If so, I dont use it and I am not a fan of it for two reasons.
        Firstly, if you are not nearby and everything cools down, the print will lift from the bed.
        Secondly, the ones that I have tried re home before commencing again. They never go back to the exact same spot and is always off just a touch.
        If the print shits itself, I just restart it.

        Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

        A Former User? 1 Reply Last reply Reply Quote 0
        • A Former User?
          A Former User @Cherno Alpha
          last edited by A Former User

          @cherno-alpha said in 3DP1000 Duet Ethernet Conversion:

          @bearer Is this like the Power Resume Feature?

          yeah. but the online config tool has a bug and renders the config useless if you enable the power loss / resume function. but if you don't plan on using that then go forth and configure without worries:) with one less worry:)

          Cherno Alphaundefined droftartsundefined 3 Replies Last reply Reply Quote 0
          • Cherno Alphaundefined
            Cherno Alpha @A Former User
            last edited by

            @bearer There will be plenty of worrying when configuring it. Never really done this type of thing before, but I have figured out most of the other things with printers. I am an expert on repairing my Raise3d machines 😄

            Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

            1 Reply Last reply Reply Quote 0
            • droftartsundefined
              droftarts administrators @A Former User
              last edited by

              @bearer The Configurator code has been fixed on Github (and network has been put back at the beginning of config.g, so at least people should be able to connect to DWC), just waiting for the online configurator to be updated.

              Ian

              Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

              1 Reply Last reply Reply Quote 0
              • droftartsundefined
                droftarts administrators @A Former User
                last edited by

                @bearer Actually, it's already been updated and M911 in config.g has double quotes around it, but you have to clear cache to make your browser use the latest version. From Christian:

                Check for version 2.0.1
                Can be seen on the start page. If it displays v2.0.0, clear your browser cache

                And my mistake, the network code hasn't been moved back to the beginning yet.

                Ian

                Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                1 Reply Last reply Reply Quote 0
                • Cherno Alphaundefined
                  Cherno Alpha
                  last edited by

                  The Duet has arrived, I am looking at a piezo bed levelling system for this, is it fiddly to set up and is it reliable? Alternatively what is the most user friendly bed levelling system? The bed is glass.

                  Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @Cherno Alpha
                    last edited by

                    @Cherno-Alpha said in 3DP1000 Duet Ethernet Conversion:

                    what is the most user friendly bed levelling system?

                    Therein lies the rub. They're all pretty picky in some way or another. Pick your poison.

                    https://duet3d.dozuki.com/Wiki/Choosing_a_Z_probe

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 0
                    • Cherno Alphaundefined
                      Cherno Alpha @nhof
                      last edited by

                      @nhof Just looked at the expansion board and I need to get one, problem is the Australian reps dont have any at all so will have to get them from overseas. Yay for freight charges.

                      Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                      1 Reply Last reply Reply Quote 0
                      • Cherno Alphaundefined
                        Cherno Alpha
                        last edited by

                        Ok, so I have installed the duet ethernet, and the expansion board to go with it.

                        The problem that I am encountering at the moment is with the Z axis.

                        X and Y home and operate perfectly.

                        Z is the issue.

                        We have been able to get Z to home. Once home, if you press + 5mm it does not operate. If I go - 5mm it tries to drive the hotend through the printer.
                        The Z dive height has been set to 0.

                        To continue testing we have to manually wind the Z axis to try something new.

                        Any suggestions to try would be great.

                        Thanks,
                        Brad

                        Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                        Phaedruxundefined 1 Reply Last reply Reply Quote 0
                        • Dougal1957undefined
                          Dougal1957
                          last edited by

                          try posting your config.g and homing files then we can all have a look and see if there is anything obvious.

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator @Cherno Alpha
                            last edited by

                            @Cherno-Alpha said in 3DP1000 Duet Ethernet Conversion:

                            The Z dive height has been set to 0.

                            Why would you set it to 0?

                            Have you seen this? https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Homing_Z

                            We'd need to see your config and homing files.

                            Z-Bot CoreXY Build | Thingiverse Profile

                            1 Reply Last reply Reply Quote 0
                            • Cherno Alphaundefined
                              Cherno Alpha
                              last edited by

                              @Dougal1957 , @Phaedrux
                              Will post the data below,

                              We set it to 0 after the first time we were setting the other axes it tried to drive it down. It is only at 0 till we have it sorted.

                              Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                              1 Reply Last reply Reply Quote 0
                              • Cherno Alphaundefined
                                Cherno Alpha
                                last edited by

                                Z HOME
                                ; homez.g
                                ; called to home the Z axis
                                ;
                                ; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Sep 17 2019 17:44:51 GMT+1000 (Australian Eastern Standard Time)
                                G91 ; relative positioning
                                G1 Z0 F6000 S2 ; lift Z relative to current position
                                G1 S1 Z-505 F3600 ; move Z down until the endstop is triggered
                                G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                                ; Uncomment the following lines to lift Z after probing
                                ;G91 ; relative positioning
                                ;G1 S2 Z0 F100 ; lift Z relative to current position
                                ;G90 ; absolute positioning

                                Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                1 Reply Last reply Reply Quote 0
                                • Cherno Alphaundefined
                                  Cherno Alpha
                                  last edited by

                                  CONFIG FILE

                                  ; Configuration file for Duet WiFi (firmware version 2.03)
                                  ; executed by the firmware on start-up
                                  ;
                                  ; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Sep 17 2019 17:44:50 GMT+1000 (Australian Eastern Standard Time)

                                  ; General preferences
                                  G90 ; send absolute coordinates...
                                  M83 ; ...but relative extruder moves
                                  M550 P"3DP Duet" ; set printer name

                                  ; Network
                                  M552 P192.168.1.14 S1 ; enable network and set IP address
                                  M553 P255.255.255.0 ; set netmask
                                  M554 P192.168.1.1 ; set gateway
                                  M586 P0 S1 ; enable HTTP
                                  M586 P1 S0 ; disable FTP
                                  M586 P2 S0 ; disable Telnet

                                  ; Drives
                                  M569 P5 S1 ; physical drive 5 goes forwards
                                  M569 P6 S0 ; physical drive 6 goes backwards
                                  M569 P7 S1 ; physical drive 7 goes forwards
                                  M569 P3 S1 ; physical drive 3 goes forwards
                                  M569 P4 S1 ; physical drive 4 goes forwards
                                  M584 X5 Y6 Z7 E3:4 ; set drive mapping
                                  M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
                                  M92 X128.00 Y128.00 Z1600.00 E420.00:420.00 ; set steps per mm
                                  M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                                  M203 X6000.00 Y6000.00 Z60.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
                                  M201 X500.00 Y500.00 Z5.00 E250.00:250.00 ; set accelerations (mm/s^2)
                                  M906 X800 Y800 Z800 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
                                  M84 S30 ; Set idle timeout

                                  ; Axis Limits
                                  M208 X0 Y0 Z0 S1 ; set axis minima
                                  M208 X1000 Y1000 Z500 S0 ; set axis maxima

                                  ; Endstops
                                  M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

                                  ; Z-Probe
                                  M558 P0 H0 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
                                  M557 X100:800 Y100:800 S200 ; define mesh grid

                                  ; Heaters
                                  M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
                                  M143 H0 S140 ; set temperature limit for heater 0 to 140C
                                  M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
                                  M143 H1 S280 ; set temperature limit for heater 1 to 280C
                                  M305 P2 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 2
                                  M143 H2 S280 ; set temperature limit for heater 2 to 280C

                                  ; Fans
                                  M106 P0 S1 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
                                  M106 P1 S1 I0 F500 H2 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

                                  ; Tools
                                  M563 P0 D0 H1 F0 ; define tool 0
                                  G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                  G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                                  M563 P1 D1 H2 F0 ; define tool 1
                                  G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                                  G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

                                  ; Custom settings are not defined

                                  Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                  1 Reply Last reply Reply Quote 0
                                  • Cherno Alphaundefined
                                    Cherno Alpha
                                    last edited by

                                    HOME X
                                    This Axis is functioning correctly, so I thought I would also post this as well just to provide further information.

                                    ; homex.g
                                    ; called to home the X axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Sep 17 2019 17:44:50 GMT+1000 (Australian Eastern Standard Time)
                                    G91 ; relative positioning
                                    G1 Z0 F6000 S2 ; lift Z relative to current position
                                    G1 S1 X-1005 F3600 ; move quickly to X axis endstop and stop there (first pass)
                                    G1 X5 F6000 ; go back a few mm
                                    G1 S1 X-1005 F300 ; move slowly to X axis endstop once more (second pass)
                                    G1 Z0 F6000 S2 ; lower Z again
                                    G90 ; absolute positioning

                                    Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                    1 Reply Last reply Reply Quote 0
                                    • nhofundefined
                                      nhof
                                      last edited by

                                      Does Z axis travel correctly normally?

                                      Note that the motors probably have a minimum pulse width of 3us, so you may have to guarantee this in order for the motors to run properly at higher step rates.

                                      Something like:

                                      M569 P5 S1 T3
                                      M569 P6 S1 T3
                                      M569 P6 S1 T3
                                      

                                      Depending on what machine you have the motors will either be these: https://www.applied-motion.com/sites/default/files/hardware-manuals/STM23R Hardware Manual 920-0056D.pdf

                                      or these: https://www.applied-motion.com/sites/default/files/hardware-manuals/TSM23P-Hardware Manual_920-0083B.pdf

                                      Just look at the connectors.

                                      Cherno Alphaundefined 1 Reply Last reply Reply Quote 0
                                      • Cherno Alphaundefined
                                        Cherno Alpha @nhof
                                        last edited by

                                        @nhof
                                        Thanks for the advice. I will have a look and test to see how that goes.

                                        Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                        1 Reply Last reply Reply Quote 0
                                        • Cherno Alphaundefined
                                          Cherno Alpha
                                          last edited by

                                          A Bit of an update.

                                          After getting my mate to spend way to much time on it troubleshooting the problematic Z axis issue, he decided to make the nema 23s just motors instead of integrated steppers. Not long after I had a fully functioning Z axis. The X and Y axes are still the integrated stepper and work well.

                                          Printer is calibrated on the XYZ axes. Tested the extruder side as well all functioning. Only thing really left to do is put the bondtech on it and the usual bed calibrations etc. Then we are off and printing.

                                          Thanks for all the assistance in getting this up and running.

                                          Brad

                                          Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                          1 Reply Last reply Reply Quote 1
                                          • Cherno Alphaundefined
                                            Cherno Alpha
                                            last edited by

                                            Some good news but also some bad news.

                                            Everything is working so to speak. Ran the first print, and I am getting layer shift on the X and Y axis on every layer. Different prints different direction.
                                            I am using Ideamaker as the slicer, I do not think this is the issue, but it is information.

                                            The X and Y axis are still controlled by the integrated steppers.
                                            As the print continues it gets progressively worse.

                                            See below for the config file.

                                            ; Configuration file for Duet WiFi (firmware version 2.03)
                                            ; executed by the firmware on start-up
                                            ;
                                            ; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Sep 24 2019 14:17:15 GMT+1000 (Australian Eastern Standard Time)

                                            ; General preferences
                                            G90 ; send absolute coordinates...
                                            M83 ; ...but relative extruder moves
                                            M550 P"Unicorns are not Fucking Real" ; set printer name

                                            ; Network
                                            M552 P192.168.1.14 S1 ; enable network and set IP address
                                            M553 P255.255.255.0 ; set netmask
                                            M554 P192.168.1.1 ; set gateway
                                            M586 P0 S1 ; enable HTTP
                                            M586 P1 S0 ; disable FTP
                                            M586 P2 S0 ; disable Telnet

                                            ; Drives
                                            M569 P5 S1 ; physical drive 5 goes forwards
                                            M569 P6 S0 ; physical drive 6 goes backwards
                                            M569 P2 S1 ; physical drive 2 goes forwards
                                            M569 P3 S1 ; physical drive 3 goes forwards
                                            M569 P4 S1 ; physical drive 4 goes forwards
                                            M584 X5 Y6 Z2 E3:4 ; set drive mapping
                                            M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
                                            M92 X128.25 Y128.25 Z1600.00 E425.00:425.00 ; set steps per mm
                                            M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                                            M203 X6000.00 Y6000.00 Z300.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
                                            M201 X500.00 Y500.00 Z5.00 E250.00:250.00 ; set accelerations (mm/s^2)
                                            M906 X1000 Y1000 Z1600 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
                                            M84 S30 ; Set idle timeout

                                            ; Axis Limits
                                            M208 X0 Y0 Z0 S1 ; set axis minima
                                            M208 X1000 Y1000 Z500 S0 ; set axis maxima

                                            ; Endstops
                                            M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

                                            ; Z-Probe
                                            M558 P0 H2 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
                                            M557 X100:800 Y100:800 S200 ; define mesh grid

                                            ; Heaters
                                            M140 H-1 ; disable heated bed
                                            M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
                                            M143 H1 S280 ; set temperature limit for heater 1 to 280C
                                            M305 P2 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 2
                                            M143 H2 S280 ; set temperature limit for heater 2 to 280C

                                            ; Fans
                                            M106 P0 S1 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
                                            M106 P1 S1 I0 F500 H2 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

                                            ; Tools
                                            M563 P0 D0 H1 F0 ; define tool 0
                                            G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                            G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                                            M563 P1 D1 H2 F0 ; define tool 1
                                            G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                                            G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

                                            ; Custom settings are not defined

                                            Ultimaker 2, Raise3d N2 Plus, 3DP1000, Creaform Go!Scan 50, Creaform Handyscan700

                                            Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA