Constant layer shift along y-axis
-
Here is my config
- ; Drives
- M569 P0 S1 ; physical drive 0 goes forwards
- M569 P1 S1 ; physical drive 1 goes forwards
- M569 P2 S1 ; physical drive 2 goes forwards
- M569 P3 S0 ; physical drive 3 goes forwards
- M584 X0 Y1 Z2 E3 ; set drive mapping
- M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
- M92 X80.00 Y80.00 Z400.00 E180.00 ; set steps per mm
- M566 X30.00 Y30.00 Z30.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
- M203 X6000.00 Y6000.00 Z1200.00 E1200.00 ; set maximum speeds (mm/min)
- M201 X500.00 Y500.00 Z50.00 E1000.00 ; set accelerations (mm/s^2)
- M906 X1500 Y1700 Z1500 E1700 I30 ; set motor currents (mA) and motor idle factor in per cent
- M84 S30 ; Set idle timeout
- ; Axis Limits
- M208 X0 Y0 Z0 S1 ; set axis minima
- M208 X220 Y220 Z220 S0 ; set axis maxima
- ; Endstops
- M574 X1 Y1 Z2 S1 ; set active low and disabled endstops
- ; Z-Probe
- M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
- M558 P9 H10 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
- G31 P500 X0 Y0 Z3.0 ; set Z probe trigger value, offset and trigger height
- M557 X50:220 Y10:180 S42.5 ; define mesh grid
- ; Heaters
- M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
- M143 H0 S120 ; set temperature limit for heater 0 to 120C
- M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
- M143 H1 S280 ; set temperature limit for heater 1 to 280C
- ; Fans
- M106 P0 S0.3 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
- M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
- M106 P2 S1 I0 F500 H1 T45
- ; Tools
- M563 P0 D0 H1 F0 ; define tool 0
- G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
- G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
and some photos. I use linear rails..
-
How did you ensure that the Z axis was orthogonal to both X and Y when you built the machine?
-
your frame or at least your axis are not square to each other. is this the first time the printer has been assembled?
-
unrelated, but your belt path is also extremely un-parallel to the frame, which will result in different steps/mm depending on position and also belt tension.
-
Yes it is the first time this printer is assembled in that way. Nevertheless, the belt does not need to be parallel/flat to the extrusion. I rather think that one axis might not be straight, but how this should be possible in a cartesian? Even if y would be tilted 20 degree it would only matter for the first layer.
-
@dgrat said in Constant layer shift along y-axis:
Nevertheless, the belt does not need to be parallel/flat to the extrusion.
it does create a small scaling error due to the angle of the belt.
-
Testprint of 2x2x10 cm cube. The higher the print, the less is the y offset. This is a bit weird. I try to re-check the y axis.
-
I re-assembled the x-axis ensured it is more or less orthogonal and the error disappeared
-
The issue appeared again with a 10x10x2cm cube. Y is not straight.
Is there a way to log step losses? Printer is square and I supect an issue with the driver?!
Actually, I never had a similar problem with any of my printers. -
Did you correct the angle of the Y belt? Perhaps it's binding?
-
Loose pulley, check that the bed is mounted fixed