Blank Page after update of Duet Web Control
-
@Phaedrux I did try the different browser still same issue. Pulled SD card and loaded a fresh download of the DWC 2.0.7 to the card into the /www folder and still same issue. Blank screen
-
What board and firmware version?
Can you connect via USB and verify that it's actually loaded up?
M115 will give the firmware version.
M503 will try to read the contents of config.g to verify that the SD card has loaded config.g properly at startup.
M112 will give a diagnostic report. -
Maybe add
M20 S2 P"/www"to the list?And if everything looks good, the developer console in f.ex. chrome has a network tab to help identify issues as well.
(in chrome hit F12 key to bring up the developer console in a new tab then type in the url for the duet) -
@Phaedrux So it will eventually load after about 15min and everything seems to be ok. Then I wanted to see if it was fixed so reloaded the page and we are back at the blank page
-
@Phaedrux
m115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC v0.6 or 1.0 FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet 3 MB6HC FIRMWARE_DATE: 2020-01-03b3m503
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Mar 06 2020 14:56:26 GMT-0700 (Mountain Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet3 CNC" ; set printer name; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P0.3 S0 ; physical drive 0.3 goes backwards
M584 X0.0:0.3 Y0.1 Z0.2 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E80.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X14000.00 Y14000.00 Z1800.00 E14000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E500.00 ; set accelerations (mm/s^2)
M906 X2800 Y2800 Z4200 E2800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X2498 Y1245 Z130 S0 ; set axis maxima; Endstops
M574 X1 S1 P"io0.in" ; configure active-high endstop for low end on X via pin io0.in
M574 Y1 S1 P"io1.in" ; configure active-high endstop for low end on Y via pin io1.in
M574 Z2 S1 P"io2.in" ; configure active-high endstop for high end on Z via pin io2.in; Z-Probe
M558 P0 H5 F120 T12000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"temp0" Y"thermistor" T1 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M143 H0 S0 ; set temperature limit for heater 0 to 0C
M307 H0 B0 S0.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0; Fans
; Tools
; Custom settings
M307 H1 A-1 C-1 D-1 ; Disable Heater 1 so we can use it for a tool
M453 P0 R24000 F400 ; Set to CNC mode, using Tool 0, 24000 Max RPM, PWM Frequency 400hz; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
@bearer said in Blank Page after update of Duet Web Control:
M20 S2 P"/www"
M20 S2 P"/www"{"dir":"/www","first":0,"files":["html404.htm","language.xml.gz","reprap.htm.gz","*css","*fonts","*js","favicon.ico","*img","dwc.json","index.html","index.html.gz","favicon.ico.gz"],"next":0,"err":0}
-
@bearer what am I looking for in the developer console? I have it open.
-
This post is deleted! -
@Phaedrux I also seem to have just a ton of files in my system folder now. I have never seen this many before:
-
Looks like you might have accidentally placed the contents of the dwc zip file in the /sys folder instead of the /www folder.
-
@Phaedrux Wow super rookie mistake.
-
no big deal. You have a backup of your SD card from before you started updating right?
-
@Phaedrux right...... No but I guess I need the practice and the lesson.
-
@Phaedrux fixed and fixed, comes up no problem now. Thank you
