Single Macro for filament handling?

dc42

@Kolbi said in Single Macro for filament handling?:

I tried the following example but it will not work. When looking at the state.status from within a macro, it will always report 'busy'. Is there any other way, something I'm missing, that will let me know that a printer is not currently in printing something/ when it is idle (besides current macro)?

I suggest you look for state.status != "printing" instead. Here's how RRF determines state.status:

// Get the status index
size_t RepRap::GetStatusIndex() const noexcept
{
	return    (processingConfig)										? 0		// Reading the configuration file
#if HAS_LINUX_INTERFACE && SUPPORT_CAN_EXPANSION
			: (gCodes->IsFlashing() || expansion->IsFlashing())			? 1		// Flashing a new firmware binary
#else
			: (gCodes->IsFlashing())									? 1		// Flashing a new firmware binary
#endif
			: (IsStopped()) 											? 2		// Halted
#if HAS_VOLTAGE_MONITOR
			: (!platform->HasVinPower() && !gCodes->IsSimulating())		? 3		// Off i.e. powered down
#endif
			: (gCodes->IsPausing()) 									? 4		// Pausing / Decelerating
			: (gCodes->IsResuming()) 									? 5		// Resuming
			: (gCodes->IsPaused()) 										? 6		// Paused / Stopped
			: (printMonitor->IsPrinting() && gCodes->IsSimulating())	? 7		// Simulating
			: (printMonitor->IsPrinting())							  	? 8		// Printing
			: (gCodes->IsDoingToolChange())								? 9		// Changing tool
			: (gCodes->DoingFileMacro() || !move->NoLiveMovement() ||
			   gCodes->WaitingForAcknowledgement()) 					? 10	// Busy
			:															  11;	// Idle

}

Kolbi

@dc42 THANKS!

Kolbi

@dc42 said in Single Macro for filament handling?:

state.status != "printing"

So something such as following? See any pitfalls?

if state.status != "printing"

   ; Printer is not currently printing!

   if sensors.filamentMonitors[0].filamentPresent = true
   
      M291 P"Press OK to begin filament UNLOADING, else press CANCEL to exit." R"Filament Handling" S3
      M291 P"Please wait while the nozzle is being heated." T5 ; Display message
      M98 P"0:/macros/Heat Nozzle"; heat nozzle to predetermined temp
      M291 P"Ready for filament unloading. Gently pull filament and press OK." R"Filament Handling" S2
      M291 P"Retracting filament..." T5 ; Display another message
      G1 E-150 F5000 ; Retract filament
      M400 ; Wait for the moves to finish
      M292 ; Hide the message
      M84 E0 ; Turn off extruder
      G10 S0 ; Turn off the heater
      M291 P"Press OK to begin filament LOADING, else press CANCEL to exit." R"Filament Handling" S3
      M98 P"0:/macros/Filament Handling"; run again

   else

      M291 P"Press OK to begin filament LOADING, else press CANCEL to exit." R"Filament Handling" S3
      M291 P"Please wait while the nozzle is being heated." T5 ; Display message
      M98 P"0:/macros/Heat Nozzle"; heat nozzle to predetermined temp
      M291 P"Ready for filament loading. Insert filament and press OK." R"Filament Handling" S2
      M291 P"Feeding filament..." T5 ; Display new message
      G1 E150 F600 ; Feed 150mm of filament at 600mm/min
      G1 E20 F100 ; Feed 20mm of filament at 100mm/min
      G4 P1000 ; Wait one second
      G1 E-1 F1800 ; Retract 10mm of filament at 1800mm/min
      M400 ; Wait for moves to complete
      M292 ; Hide the message
      M84 E0 ; Turn off extruder
      G10 S0 ; Turn off the heater

else

   M291 P"Press OK to begin filament change, else press CANCEL to exit." R"Filament Handling" S3
   M98 P"0:/sys/filament-change.g" ; call filament-change.g
   M98 P"0:/sys/resume.g" ; call resume.g

Kolbi

@Kolbi said in Single Macro for filament handling?:

state.status != "printing"

Didn't work when printing from SD card, had to use

if state.status != "Processing"

It needs some refinement but it meets the original goal:

If anyone wants to see all the sys and macro files, they are located here: https://github.com/rkolbi/RRF-machine-config-files/tree/master/Prusa MK3s

Kolbi

I updated the macro set abit. Now the load/unload routine sets the filament type system-wide / in DWC. This is good because then when in DWC, it shows the correct filament loaded and also that if you're using the filament config.g you're good to go.
The other change is that the 'Set Filament Type' macro will not let you change filament type if the filament is currently loaded - makes sense to me.
Since I don't use DWC when normally using the printer, the load/unload filament macros within DWC are empty - when in DWC I'll still use my macro.

The three macro files are here:
https://github.com/rkolbi/RRF-machine-config-files/tree/master/Prusa MK3s/macros

I'm happy with the macro set operation and usability. If you have any thoughts on how to improve them please let me know.

Cheers,
Kolbi

Phaedrux

Well done.

Kolbi

@Phaedrux Thanks!

Kolbi

This is the latest version - most likely won't change until variables are enabled in the firmware.

Use the included Macros for filament handling.
To make filament loading, unloading, and changing the most straightforward and simplistic possible evolution, I have made a macro set that is readily accessible from the PanelDue. To take full advantage of the duet filament system you will need to make the system filaments PLA, PETG, ABS, and PC. This will allow you to have custom instructions for each different filament, by adding such to the filament's config.g file. !Note: Based on my current macro version, it is required that each filament's load.g and unload.g remain empty. Placing code into these files will make these macro fail.
"Set Filament Type" asks what type filament you are going to use; PLA, PETg, ABS, or PC. Based on the selection, this macro rewrites the "Heat Nozzle" macro to heat the nozzle for the selected filament type. !Note: This macro only has to be executed once for the given filament type change as it's settings are nonvolatile, regardless of reset or power off. !Note: The script will not let you change the filament type while filament is loaded.
"Filament Handling" is for any filament unloading, loading, and changing regardless of the printer's state, printing or not. This macro will load, unload, and change filament based on two conditions; whether it detects filament is currently loaded or not, and if a print is in progress or not. !Note: The logic function in the macro retrieves the current status of the filament sensor to base the perceived desired action to enact. If your printer's filament is currently empty and you intend to load filament, please do not place it into the extruder until requested to do so by the macro. Else the macro will determine that filament is loaded and that you desire to unload filament, instead of load.
"Heat Nozzle" is created by the "Set Filament Type" macro and can be selected to heat the hotend to the set temperature for the last chosen filament type. You do not need to run this to change filament, the "Filament Handling" macro automatically runs this macro to perform the heating of the hotend to carry out the filament handling, whether it be loading, unloading, or changing.

/macros

/macros/Filament Handling

; 0:/macros/Filament Handling
; Macro used for all filament handling evolutions

if state.status != "processing"                            ; Printer is not currently printing!

   if sensors.filamentMonitors[0].filamentPresent = true   ; Filament is detected, currently loaded
   
      M291 P"Press OK to begin filament UNLOADING, else press CANCEL to exit." R"Filament Handling" S3
      M98 P"0:/macros/Heat Nozzle"                         ; Heat nozzle to predetermined temp
      M291 P"Ready for filament unloading. Gently pull filament and press OK." R"Filament Handling" S2
      M291 P"Retracting filament..." T5                    ; Display another message
      G1 E-150 F5000                                       ; Retract filament
      M400                                                 ; Wait for the moves to finish
      T0 M702                                              ; Select tool 0, set filament is unloaded
      M104 S-273                                           ; Turn off hotend
      M140 S-273                                           ; Turn off heatbed
      M98 P"0:/macros/Filament Handling"; run again        ; Now that filament is unloaded, lets ask to load filament

   else

      M291 P"Press OK to begin filament LOADING, else press CANCEL to exit." R"Filament Handling" S3
      M98 P"0:/macros/Heat Nozzle"                         ; Heat nozzle to predetermined temp
      M291 P"Ready for filament loading. Insert filament and press OK." R"Filament Handling" S2
      M291 P"Feeding filament..." T5                       ; Display new message
      G1 E150 F450                                         ; Feed 150mm of filament at 600mm/min
      G1 E20 F100                                          ; Feed 20mm of filament at 100mm/min
      G4 P1000                                             ; Wait one second
      G1 E-1 F1800                                         ; Retract 10mm of filament at 1800mm/min
      M400                                                 ; Wait for moves to complete
      M98 P"0:/sys/filaset"                                ; Set system filament type
      M400                                                 ; Wait for moves to complete
      M104 S-273                                           ; Turn off hotend
      M140 S-273                                           ; Turn off heatbed

else

   M291 P"Press OK to begin filament CHANGE, else press CANCEL to exit." R"Filament Handling" S3
   M98 P"0:/sys/filament-change.g"                         ; Call filament-change.g
   M24                                                     ; Start/resume SD print

/macros/Heat Nozzle

; 0:/macros/Heat Nozzle
; Heat nozzle to set temp

M291 R"Filament Handling" P"Heating nozzle for PETg, please wait." S0 T10
T0                                                         ; Select Tool 0
M109 S230                                                  ; set temp to 230c and wait

/macros/Set Filament Type

; 0:/macros/Set Filament Type
; Macro used to set system's loaded filament type

if sensors.filamentMonitors[0].filamentPresent = false        ; if filament is loaded then reject action to change filament type

  M291 P{"System filament is currently set to " ^ move.extruders[0].filament ^ ". Press OK to change filament type, else press CANCEL to exit."} R"Filament Handling" S3

  ; Set PLA temp
  M28 "0:/macros/Heat Nozzle"                                 ; Begin writing to SD card file
  M291 R"Filament Handling" P"Heating nozzle for PLA, please wait." S0 T10
  T0                                                          ; Activate Hotend
  M109 S200                                                   ; set temp to 200c and wait
  M29                                                         ; Stop writing to SD card
  
  M28 "0:/sys/filaset"                                        ; Begin writing to SD card file
  T0 M702                                                     ; Set system filament as UNLOADED
  T0 M701 S"PLA"                                              ; Set system filament as PLA
  M29                                                         ; Stop writing to SD card

  M291 S3 R"Filament Handling" P"Filament type currently set to PLA. Press cancel to save this selection or OK to proceed to next filament type."
  
  ; Set PETg temp
  M28 "0:/macros/Heat Nozzle"                                 ; Begin writing to SD card file
  M291 R"Filament Handling" P"Heating nozzle for PETg, please wait." S0 T10
  T0                                                          ; Activate Hotend
  M109 S230                                                   ; set temp to 230c and wait
  M29                                                         ; Stop writing to SD card
  
  M28 "0:/sys/filaset"                                        ; Begin writing to SD card file
  T0 M702                                                     ; Set system filament as UNLOADED
  T0 M701 S"PETG"                                             ; Set system filament as PETG
  M29                                                         ; Stop writing to SD card

  M291 S3 R"Filament Handling" P"Filament type currently set to PETg. Press cancel to save this selection or OK to proceed to next filament type."

  ; Set ABS temp
  M28 "0:/macros/Heat Nozzle"                                 ; Begin writing to SD card file
  M291 R"Filament Handling" P"Heating nozzle for ABS, please wait." S0 T10
  T0                                                          ; Activate Hotend
  M109 S250                                                   ; set temp to 250c and wait
  M29                                                         ; Stop writing to SD card
  
  M28 "0:/sys/filaset"                                        ; Begin writing to SD card file
  T0 M702                                                     ; Set system filament as UNLOADED
  T0 M701 S"ABS"                                              ; Set system filament as ABS
  M29                                                         ; Stop writing to SD card

  M291 S3 R"Filament Handling" P"Filament type currently set to ABS. Press cancel to save this selection or OK to proceed to next filament type."

  ; Set PC temp
  M28 "0:/macros/Heat Nozzle"                                 ; Begin writing to SD card file
  M291 R"Filament Handling" P"Heating nozzle for PC, please wait." S0 T10
  T0                                                          ; Activate Hotend
  M109 S270                                                   ; set temp to 270c and wait
  M29                                                         ; Stop writing to SD card
  
  M28 "0:/sys/filaset"                                        ; Begin writing to SD card file
  T0 M702                                                     ; Set system filament as UNLOADED
  T0 M701 S"PC"                                               ; Set system filament as PC
  M29                                                         ; Stop writing to SD card

  M291 S3 R"Filament Handling" P"Filament type currently set to PC. Press cancel to save this selection or OK to proceed to next filament type."

else

  M291 S3 R"Filament Handling" P"Filament is currently loaded. Please unload filament before changing filament type."

filament.pdf

mitch

This post is deleted!

VirtualBrown

Is there a relatively easy way to edit these macros to work if one doesn't have a filament sensor?