Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order

    Duet 3 with Toolboard Magnetic filament monitor not working

    Duet Hardware and wiring
    3
    6
    106
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • warpster
      warpster last edited by warpster

      I just upgraded from a Duet wifi and rrf 2.5, first to rrf3.2 then I upgraded the Duet wifi to a Duet 3 and Toolboard. Everything is working except for the magnetic filament monitor. As long as I have the config line in config.g I get errors of "Extruder 0 reported 'noDataReceived' when I try to print, whether enabled or not in config.g. As soon as I start printing I get the error, maybe after 5-10 inches of filament. The Duet 3 is connected in standalone mode.

      The lights on the magnetic filament sensor act normal, I get the 3 green at startup then it alternates red/green. Not sure during printing since it errors so quickly.

      My config line is: (toolboard is 20)
      M591 D0 P3 C"20.io1.in" S1 R30:180 E3.0 A0 L24.72

      I double checked the wiring and it is correct as in the attached pictures.
      20210111_113726.jpg 20210111_113752.jpg

      I'm not sure where to go from here..thanks for any help.

      1 Reply Last reply Reply Quote 0
      • alankilian
        alankilian last edited by alankilian

        Connector.png

        Is it possible that the black wire is not fully inserted into this connector?

        Since the lights work, you know you've got power and ground connected.

        (I know nothing about toolboards, so maybe there's more setup involved.)

        Also, just a tip from someone who has done this before, It would be better to use more standard wire colors.

        You've got:
        Red = Ground
        Black = Signal
        Yellow = 3.3 Volts.

        It's better to use:
        Black = Ground
        Red = Power
        Yellow (or whatever you have) = Signal

        SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

        warpster 2 Replies Last reply Reply Quote 1
        • warpster
          warpster @alankilian last edited by

          @alankilian Thanks for the feedback, yes the black wire is well seated. That pigtail actually came with the toolboard (toolboard end wired). I had to add the connector on the filament sensor end and I have checked the wiring. Oh and I agree on the colors but that is what it came with so I used that.

          1 Reply Last reply Reply Quote 0
          • Phaedrux
            Phaedrux Moderator last edited by

            Can you confirm that 3.2 is installed on both the Duet3 and the toolboard?

            Can you provide the results of M122 and M122 B1

            https://duet3d.dozuki.com/Wiki/Duet_3_firmware_configuration_limitations

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • warpster
              warpster @alankilian last edited by

              @alankilian Well you got me thinking about the cable again so I removed it to test it better and there was a bad connection (on the end I did) that I missed. Doing a print now but I think I'm good. Thanks for making me double check!

              1 Reply Last reply Reply Quote 1
              • alankilian
                alankilian last edited by

                That's great news!

                SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                1 Reply Last reply Reply Quote 0
                • First post
                  Last post
                Unless otherwise noted, all forum content is licensed under CC-BY-SA