duet 2 wifi 3.2.2 bltouch height map way off
-
hi guys. so upgraded. got most squared away I think.
leveled bed with paper just like I did on old firmware but the map looks way way off
M558
Z Probe 0: type 9, input pin zprobe.in, output pin nil, dive height 2.5mm, probe speed 180mm/min, travel speed 6000mm/min, recovery time 0.00 sec, heaters normal, max taps 1, max diff 0.03bed preheated to 70c
M I missing something ? -
If there some tilt in the print head or BLtouch mount such that it has a different trigger height depending on location?
Where are you setting Z0 before running G29?
Post your gcode files so we can see what's going on.
-
@phaedrux I think I found my mistake . ended up tweaking my x and y and reducing probe number
M557 X10:300 Y10:320 S50 ;M557 X0:305 Y0:315 S25 new and old& G31 P500 X-42.4 Y0 Z2.883 I hope its right
after all that I ran G32 and each time adjusted each corner little by little .
did first print not too bad I dont think its compensating as good as before .
-
@phaedrux also my start g code
M106 S0 ; turn off cooling fan
G28
G29 S1
G92 E0 ; Reset Extruder
G1 Z10.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X344.5 Y300 Z0.28 F5000.0 ;Move to start position
G1 X344.5 Y90.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X344.7 Y90.0 Z0.28 F5000.0 ;Move to side a little
G1 X344.7 Y300 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ; reset extrusion distance
G1 Z15.0 F6000 ;Move the nozzle up 15mm
G92 E0 ; Reset the extruder's origin
M117 -
Post your config.g, homeall.g and bed.g as well.
-
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:05 GMT-0400 (Eastern Daylight Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"DUET3D" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E391.455 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X-5.5 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z0 ; configure Z-probe endstop on Z; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-42.4 Y0 Z2.883 ; set Z probe trigger value, offset and trigger height
M557 X10:300 Y10:320 S50 ;M557 X0:305 Y0:315 S25 ; define mesh grid; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
;M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
;M140 H0 ; map heated bed to heater 0
;M143 H0 S120 ; set temperature limit for heater 0 to 120C
;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
;M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
;M143 H1 S280 ; set temperature limit for heater 1 to 280C; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; set temperature limit for heater 1 to 300C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings
M591 D0 P2 C3 S1 ; Filament Run out sensor
G29 S1 ; Load mesh bed; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power losshere's homeall
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:06 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 H2 Z2.5 F6000 ; lift Z relative to current position
G1 H1 X-360.5 Y-355 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-360.5 Y-355 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 X140 Y160 F6000 ; go to first probe point
G30& Bed
M561 ; clear any bed transform
G29 ; probe the bed and enable compensation -
@ap742 said in duet 2 wifi 3.2.2 bltouch height map way off:
; Custom settings
M591 D0 P2 C3 S1 ; Filament Run out sensor
G29 S1 ; Load mesh bedDon't load the mesh in config.g. You haven't homed the printer yet.
@ap742 said in duet 2 wifi 3.2.2 bltouch height map way off:
G31 P500 X-42.4 Y0 Z2.883
This says the probe is 42mm to the left of the nozzle. Is that correct?
-
@phaedrux said in duet 2 wifi 3.2.2 bltouch height map way off:
G29 S1 ; Load mesh bed
so leave it out and let the slicer do it?
-
@phaedrux said in duet 2 wifi 3.2.2 bltouch height map way off:
G31 P500 X-42.4 Y0 Z2.883
yes . its Hemera hotend . its exactly -42.4 on the left side of the nozzle I didn't know if I should round this
not my hot end but close enough -
@ap742 said in duet 2 wifi 3.2.2 bltouch height map way off:
@phaedrux said in duet 2 wifi 3.2.2 bltouch height map way off:
G29 S1 ; Load mesh bed
so leave it out and let the slicer do it?
Yeah, you already have it in your slicer start gcode after the homing is done, so that's a good place for it.
The heightmap would indicate there is some tilt. Is that not the case? Some manual leveling should take care of that.
-
@phaedrux said in duet 2 wifi 3.2.2 bltouch height map way off:
Yeah, you already have it in your slicer start gcode after the homing is done, so that's a good place for it.
The heightmap would indicate there is some tilt. Is that not the case? Some manual leveling should take care of that.Thank you so much for holding my hand.
