HELP! Duet 2 WiFi Configuration and DWC Upload???

Phaedrux

@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:

Real quick. To be clear down for Z axis is Z+, Left for X is X-, and Front for Y is Y-?
Cuz that's what I have it as now.

That is correct.

@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:

-I ran a test where I had all 3 homed, then jogged all three to their centers and hit home all and the x and y were going to the wrong corner (left front instead of back right[where the endstops are]) should I go back in config.g and change some S0's to S1's?

No, you'll need to change the homeall.g file as I posted above.

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sat May 01 2021 17:31:12 GMT-0700 (Pacific Daylight Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X240 Y240 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X-5 Y-5 F6000       ; go back a few mm
G1 H1 X240 Y240 F240  ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-315 F240        ; move Z down stopping at the endstop
G90                     ; absolute positioning

You changed homex.g and homey.g already?

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sat May 01 2021 17:31:12 GMT-0700 (Pacific Daylight Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X240 F3000 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X-5 F6000    ; go back a few mm
G1 H1 X240 F240  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sat May 01 2021 17:31:12 GMT-0700 (Pacific Daylight Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y240 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y-5 F6000    ; go back a few mm
G1 H1 Y240 F240  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90

@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:

-when the extruder head is in close proximity to the back right it seems to find the correct corner just fine when homed, but if I'm far away it crashes into the opposite corner.

I'm not sure what you mean by that.

PCNoobNeedsMajorHelp

@phaedrux

Ok, I changed those values and I rechecked each home (x,y,z) individually, and then Home All.
Homeall chage successfully.png

-Everything seems to be working normal now.

-I'll calibrate some things and run a test print.

Thanks,

-Carson

PCNoobNeedsMajorHelp

@phaedrux

So, I'm trying to calibrate my E-steps, but it seems no matter how slow I try to set it, it goes fast, and no matter what length I set it to extrude, it seems to extrude forever until I eventually have to E stop it, so I don't waste filament .

The guide says to run G1 E100 F60, and 60mm/sec is pretty fast but I ran it anyway. But it says to set it low, so I manually hit 1mm/sec and to extrude 100mm and I got the same results for both...Fast and never ending filament extrusion.

-Not sure what to do

Thanks

-Carson

Phaedrux

@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:

G1 E100 F60, and 60mm/sec

F60 is 60mm/min, so only 1mm/s which is slow.

If it's still going very fast it could be that your steps per mm is very wrong from what it should be.

What is the extruder? The default creality bowden setup for the ender5?

M92 X80.00 Y80.00 Z400.00 E420.00

E420 could be quite wrong if it's teh stock. I think it would be more like E90

PCNoobNeedsMajorHelp

@phaedrux

It's a Micro-Swiss All Metal Hotend Direct Drive.

But yeah it's going really fast. In about 15 sec i had like over 300mm. And it just keeps going and going.

config.g e steps prob.png

Phaedrux

@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:

It's a Micro-Swiss All Metal Hotend Direct Drive

And what kind of motor on it? 200 or 400 steps per rotation?

Like this?

https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder

PCNoobNeedsMajorHelp

@phaedrux

Yes, that's the correct one, although it didn't come with a motor so I'm using the Ender 5 stock motor which is 400 (I'm almost positive it's a 400 step motor 99.9%)

Thanks

-Carson

Phaedrux

Well if it's extruding way too much with 400 steps per mm, try 100 steps per mm. Extrude a small amount to start with to see how it goes.

M92 E100
G1 E10 F60

PCNoobNeedsMajorHelp

@phaedrux

So after changing M92 in the config file, and commanding G1 E10 F60, it is now extruding at a slow speed but I think it's still extruding too much. If I'm understanding the command correctly E=Speed and F= mm of filament to be extruded, correct?

-I ran the command 3 times and got a length of 100mm each time.

-Am I missing something, or is that what was supposed to happen?

Thanks,

-Carson

engikeneer

@pcnoobneedsmajorhelp in a G1 command, E is the amount of movement command from the Extruder in mm. F is the feedrate (speed) in mm/min.

Did you reboot after changing the M92 in config.g?

Also, you can just send the M92 command in the console in the web control (e.g. while you're setting it up to find the right value), then update the config when you've found the right value to use.

Edit: the amount of extruder movement is measured in mm of raw filament being fed into the hotend. Of you're commanding 10.. and it's pushing through 100mm, then your M92 value must be 10x too high

PCNoobNeedsMajorHelp

@engikeneer

Well that didn't work. I tried it all the way down to 4 and it just keeps going forever. Or not going enough. every time i try it i get a different result. Plus when have you ever hear of a stock ender stepper motor doing lower than 93. Also i noticed that my PanelDue is not in sync with the DWC and it also wont send commands from the PanelDue (unresponsive).

PCNoobNeedsMajorHelp

@engikeneer

Now the DWC is not responding. And yes I'm connected to WiFi

Phaedrux

Is it possible you've sent a very long running command causing things to appear unresponsive?

Do things return to normal after a power cycle?

How have you set the steps per mm and what command are you sending for the extruder test?

PCNoobNeedsMajorHelp

@phaedrux

I've cycled the power several times and it still either isn't responsive or is a never ending extrusion. I first had it at 100, then I tried 10, then 4, 14, 15, 8, and lastly 16 and out of all those 8 was the closest at 25mm so I tried 16 to see if I could get close when I set it at 50mm. All the other ones either ran forever or were just way too long. There doesn't seem to be any rhyme or reason to it either. So I have 2 theories. 1: (there are relatives in town using up more bandwidth than usual so..) slow internet connection=lag in responsiveness. Or 2: the motor is broken.

-On the DWC I've commanded E10 F100, E10 F60. After than I manually clicked it to feed 10mm, at a speed of 1, then 5, then 30(which was wayyyy too fast). Then I tried 100mm at 1 and 5. And they don't reflect at all on my PanelDue.

Phaedrux

Can you post your current config as it is now so we can see what it's setup like?

It's an ungeared extruder, so the steps per mm will be pretty low regardless of the motor.

Have you tried following along with this? https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40#s165

PCNoobNeedsMajorHelp

@phaedrux

Yes, I'm using the guide.

EXT PROB.png
EXT PROB2.png
EXT#1.png
EXT#2.png
EXT#3.png
EXT#4.png

Phaedrux

You can add T0 to the end of your config.g so that the first tool is selected at startup.

I would suspect that the M92 E steps per mm is in the range of 90 - 120.

Extruding 100mm at 1mm/s will take... 100 seconds if the steps per mm are accurate, so you will need to be patient.

PCNoobNeedsMajorHelp

@phaedrux

Yes, I know this lol, that's why this is so frustrating and infuriating, because it's not even close. That's why I had my E steps set at 9, because nothing else is working and I'm ready to throw this thing out of the window.

-For example...Here is a picture of my screen, this is what I'm running... and then these are the results of the execution of that specific setting on the screen.

For reference I put this 45mm(long end) Allen Key compared to the filament that came out. In maybe 30sec

Screen for over extrusion #1.jpg
Screen for over extrusion #2.jpg
Over Extrusion.jpg
Current E-steps while running this test
Current Esteps.png

I really hope it's something stupid and obvious that I'm doing wrong or just not doing altogether, because I'm starting to worry. And, I mean.... I've just put so many hours into this build, ya know, and to have it be obliterated because of an e-step issue would be enough for me to just go back to my old board out of frustration. I just want to PRINT. Rant over. Sorry bout that, just had to get that out of my system.

Thanks,

-Carson

PCNoobNeedsMajorHelp

@pcnoobneedsmajorhelp

If I need to send a video file of what's happening, I will.

Oh, and here's what the screen of my PanelDue looks like during all this. It's like its not in sync with the DWC

Phaedrux

You measure the filament going INTO the extruder, not out of it. You really need to look at that guide.