G29 deploys before raising
-
@rjenkinsgb ok, maybe I was not too specific. Here is more details:
- G30 works ok, and is not related to this problem.
- Yes, the printer needs to be homed when running G29 (this means running G28 if needed). I am doing this.
The problem is still there. If the printer is homed, is near Z=0 (for whatever reason) and G29 is run, it will not lift before deploying the probe. It should (proof is that it will do it, just the order is reversed).
-
In your mesh.g file just put a G1 Zn command to raise the probe to a suitable starting height.
Frederick
-
@token47 as @fcwilt says, you can set up a mesh.g file to ensure a minimum Z height before probing using G29 S0. Then use G29 (not G29 S0) to run the mesh probing routine.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@fcwilt and @dc42 Thank you for the response. I thought fw 2.x did not have mesh.g support (I checked documentation and code, even tried it, but I could be wrong).
As I commented on OP I intend to upgrade soon, but anyway, it seems this problem would occour even on 3.x if issuing a G29 S0 directly, which is still something to consider.
-
@token47 said in G29 deploys before raising:
@fcwilt and @dc42 Thank you for the response. I thought fw 2.x did not have mesh.g support (I checked documentation and code, even tried it, but I could be wrong).
As I commented on OP I intend to upgrade soon, but anyway, it seems this problem would occour even on 3.x if issuing a G29 S0 directly, which is still something to consider.
Yes you will need to upgrade to v3.
When you do, remember that you have to first upgrade to v3.0 and then upgrade to the desired v3.x - I use v3.3 as I am not in the mood to deal with beta version issues.
There are, of course, changes that need to be made to your config.g file. Those changes caused me to put off upgrading for quite a while. But once I actually looked into the changes I found they were not that big of a deal I went forward with upgrading to v3.3 and am very glad I did.
Frederick
-
If you still have access to DWC. Upload these 3 zip files, one at a time in the system tab. Don't extract them first. Reboot after each. Use M115 in the gcode console to verify the firmware has been applied.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/Duet2and3Firmware-3.3.zip
That will get your firmware and DWC up to date.You can see the change logs here:
https://github.com/Duet3D/RepRapFirmware/wiki/Changelog-RRF-3.xFor your config, might be a good idea to run through the configurator tool and generate a fresh set for RRF3.
https://configtool.reprapfirmware.org/StartBackup your existing config files in the sys folder in case you want to switch back to RRF2. It’s easy to switch back and forth, just upload the zip file for the version you want and then upload your config files.
These documents will come in handy during the conversion.
https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview
https://duet3d.dozuki.com/Wiki/Gcode -
By the way, what kind of probe is it?
-
@phaedrux Thank you for the procedural steps. I'm reading about the upgrade and finding courage to do the upgrade, this will help. The reason for the delay is that my setup is complex, I have a ton of macros and some advanced configs, so I keep delaying it.
-
@phaedrux It's a probe I designed myself. A crashprobe. It sits behind the HEVO carriage and is deployed by pushing it down from above (releasing a magnet). It can be easily deployed by hand (the printer will beep and wait for it) or go to the corner and press against another part. Still testing, but already much better than the older one which was driving me nuts. It has about 10mm of Z offset to the nozzle and another 6-7mm above the nozzle when retracted (I wanted a very long travel on both ways to avoid problems I was having before).
-
Take it slow and cautiously. Reduce motor currents. Have a hand near the kill switch.
Send M98 P"config.g" to check for syntax errors.
We're always here to help.
