Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    DCS is not started

    Scheduled Pinned Locked Moved
    Firmware installation
    3
    7
    195
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Rein3003undefined
      Rein3003
      last edited by Rein3003

      I tried to update the firmware on my toolchanger, but after 45 minutes it still wasn't ready. So when I restarted the printer I couldn't reconnect anymore.

      • I think it can connect to the wifi, as it knows to tell me DCS isn't started.
      • I can connect to the 6HC via pronterface, after sending M115 I can confirm that I am on the updated firmware.
      • I have a touchscreen connected to the pi so I can get into the pi's console.

      right before it tells me it failed to start DCS it tells me this: "duetcontrolserver.service: Failed with result 'protocol'."

      Duet setup:

      • 6HC
      • Pi 4 - 8gb
      • 3HC
      • 2x 1LC

      Any help would be appreciated

      gloomyandyundefined 1 Reply Last reply Reply Quote 0
      • gloomyandyundefined
        gloomyandy @Rein3003
        last edited by

        @Rein3003 Sounds like you are running in SBC mode? What version did you have installed before the update and what version were you trying to update to? What method did you use to update the software?

        Rein3003undefined 1 Reply Last reply Reply Quote 0
        • Rein3003undefined
          Rein3003 @gloomyandy
          last edited by

          @gloomyandy I had 3.3.x installed before and I tried to update to 3.4.6. I followed this guide: https://docs.duet3d.com/User_manual/RepRapFirmware/Updating_firmware

          So I basically downloaded the zip and uploaded it to dwc and I just let it do its thing.

          gloomyandyundefined 1 Reply Last reply Reply Quote 0
          • gloomyandyundefined
            gloomyandy @Rein3003
            last edited by

            @Rein3003 Are you running in SBC mode? If you are you should have followed this guide: https://docs.duet3d.com/User_manual/Machine_configuration/SBC_setup

            The system will be in SBC mode if you have a rPi attached to the Duet board and if you do not have a micro sd card in the reader of the Duet board.

            Rein3003undefined 1 Reply Last reply Reply Quote 0
            • Rein3003undefined
              Rein3003 @gloomyandy
              last edited by

              @gloomyandy Yes I'm indeed in SBC mode

              gloomyandyundefined jay_s_ukundefined 2 Replies Last reply Reply Quote 0
              • gloomyandyundefined
                gloomyandy @Rein3003
                last edited by

                @Rein3003 Ah in which case you will probably now have a mismatch between the rPi software and the Duet board. I'm not sure what the best way is to resolve that. I think you should be ok to follow the update instructions I posted above, but maybe @Phaedrux could confirm?

                1 Reply Last reply Reply Quote 0
                • jay_s_ukundefined
                  jay_s_uk @Rein3003
                  last edited by

                  @Rein3003 best to just sudo apt update && sudo apt upgrade -y

                  Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                  1 Reply Last reply Reply Quote 1
                  • First post
                    Last post
                  Unless otherwise noted, all forum content is licensed under CC-BY-SA