Brand new board not reading SD card

dc42

If you run M122 the resulting diagnostic report will say whether the card detect switch indicates that a card is present, and what the interface speed is if the firmware was able to initialize it.

Also if you send M21 to re-mount the card, it may give you a better error message.

TimVukman

Thank you very much. I was hoping there was something.

TimVukman

Ok.

I will need to go through this top to bottom again. I was able to connect to the board.

M122 returned no errors that I could tell

[[language]]
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (2 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19 running on Duet WiFi 1.0
Board ID: 08DGM-95BNL-MGPSJ-6J1DG-3S46N-TKY7W
Static ram used: 21176
Dynamic ram used: 95488
Recycled dynamic ram: 2120
Stack ram used: 4008 current, 4832 maximum
Never used ram: 7456
Last reset 00:02:08 ago, cause: power up
Last software reset reason: not available
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 27.3, current 29.5, max 47.3
Supply voltage: min 0.1, current 12.1, max 12.2, under voltage events: 0, over voltage events: 0
Driver 0: standstill
Driver 1: standstill
Driver 2: standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.000839; fastest: 0.000031
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is disabled
WiFi module is disabled
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
>>> M21
SENDING:M21
SDHC card mounted in slot 0, capacity 3.64Gb
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
ok T B:2000.0 /0.0
>>> M550 s0
SENDING:M550 S0
RepRap name: My Duet
ok T B:2000.0 /0.0
>>> M552 s0
SENDING:M552 S0
WiFi module started
ok T B:2000.0 /0.0

M21 returned:

SDHC card mounted in slot 0, capacity 3.64Gb

SENDING:M552
WiFi module is connected to access point BELL137, IP address 192.168.2.27

From here, entering the IP in my browser does not find the board / printer.

M997 S0
SENDING:M997 S0
Error: Firmware binary "DuetWiFiFirmware.bin" not found
[ERROR] Error: Firmware binary "DuetWiFiFirmware.bin" not found

M997 S1
SENDING:M997 S1
File DuetWiFiServer.bin not found

DuetDisplay gives an Error1 accessing SD card

Any suggestions?

dc42

From your M122 report:

SD card 0 detected, interface speed: 20.0MBytes/sec

That's as expected, the SD card is detected and working.

SENDING:M552
WiFi module is connected to access point BELL137, IP address 192.168.2.27

From here, entering the IP in my browser does not find the board / printer.

Run M122 again and check the reported RSSI in the Network section. Also see whether you can ping the printer's IP address.

DuetDisplay gives an Error1 accessing SD card

What did you do to provoke that message? Did you by any chance press the SD card icon on the Files list, which switches between card 1 and card 0?

TimVukman

I did not realize there were two SD ports. This could well be the reason.

I pressed the icon of the memory card on the duetdisplay. My intent was to see if it would list the files.

What should the display say and how do I switch it back?

If you press the SD card icon on the Control page of the printer below the Home All button, that should pop up a window with title "Files on card 0" and below that you should see a list of files and folders in the /gcodes folder. That list may of course be empty if you have no files there. However, the same SD card icon appears at the top left of that window. If you press that one, the title will change to "Files on card 1" and if you don't have a card 1, you will get the "Error 1" after a little while.

TimVukman

Hi
I can't yet get to the Duet Wifi Browser based interface on this printer. (Printer1)

I can see on my other printer (Printer2) that in the G-Code section, the top left corner has a Green Icon that says SD Card 0 and there is a list of files. If I click on this, I get a Red icon that says SD Card 1 - not mounted.

On my printer (Printer1), I do have a Duet Display that is connected.

There is a row of icons under the X Y Z position indicators
Two rows down is an icon for the memory card, Move Extrude Macro

This memory card icon is the one I pressed.
It says

< Files on Card 0 <_> X

The balance of the screen is blank

Pressing < in the top left did nothing
Pressing <> in the middle returned
Error 1 accessing SD Card
no files listed
Pressing <> again returns
Files on card 0
None listed

TimVukman

Hi
I redid the entire process.
I can write to the card. I put version 1.20 on it
I unzipped all the files.
I put the main gcode files in the /sys folder
I put the .bin files in the /www folder
I sent M552 S0 to stop the wifi module
I sent M552 S1 to start the wifi module
I sent M997 S0
Message returned File Not Found
M122

[[language]]
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (8 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19 running on Duet WiFi 1.0
Board ID: 08DGM-95BNL-MGPSJ-6J1DG-3S46N-TKY7W
Static ram used: 21176
Dynamic ram used: 95936
Recycled dynamic ram: 1672
Stack ram used: 4008 current, 5220 maximum
Never used ram: 7068
Last reset 00:18:03 ago, cause: power up
Last software reset reason: not available
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 36.6, current 37.9, max 38.2
Supply voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill
Driver 1: standstill
Driver 2: standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.004517; fastest: 0.000000
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19
WiFi MAC address 2c:3a:e8:0b:07:d2
WiFi Vcc 3.10, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 39416
WiFi IP address 192.168.2.27
WiFi signal strength -66dBm
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

SD card SD 0 is reported as found and interfaced at 20mb/sec

From the Duet Panel Due

The printer name "Tevo Tarantula" is showing in the red line at the top of the screen and shows as idle

No files show on the screen

If I go into messages, I get:
Correct Network Name IP address correct address displayed
19m Wifi module is idle
19m Wifi module is connected to access point
correct network name correct ip address
17m Error: Firmware binary "DuetWifiFirmware.bin" not found
5mxx Cannot initialise SD card 1: Card is unuseable
5mxx Cannot initialise SD card 1: Card is unuseable

Why is it looking for Card SD1?

TimVukman

SENDING:M21
SDHC card mounted in slot 0, capacity 3.64Gb

dc42

@TimVukman:

Hi
I can't yet get to the Duet Wifi Browser based interface on this printer. (Printer1)

I can see on my other printer (Printer2) that in the G-Code section, the top left corner has a Green Icon that says SD Card 0 and there is a list of files. If I click on this, I get a Red icon that says SD Card 1 - not mounted.

On my printer (Printer1), I do have a Duet Display that is connected.

There is a row of icons under the X Y Z position indicators
Two rows down is an icon for the memory card, Move Extrude Macro

This memory card icon is the one I pressed.
It says

< Files on Card 0 <_> X

The balance of the screen is blank

Pressing < in the top left did nothing
Pressing <> in the middle returned
Error 1 accessing SD Card
no files listed
Pressing <> again returns
Files on card 0
None listed

You must be running an older version of PanelDue firmware, which uses the <_> button to switch between card 0 and card 1. That's why it's trying to mount SD card 1 when you press that button.

Do you actually have any files in the /gcodes folder of the SD card?

TimVukman

Yes, I have all the gcode files installed.

TimVukman

As indicated earlier, it is the .bin file that is reported as not being found. That is in the /www folder.

The message from PanelDue is that Card 1 was not found.

Should I try to update the PanelDue firmware?

dc42

The .bin file should not be in the /www folder. If you intend to update the firmware from it, it needs to be in the /sys folder.

As your PanelDue firmware appears to be quite old, i suggest you update it.

TimVukman

I have been busy
I have updated the paneldue firmware to 1.17. It was actually very smooth and straight forward.
I have gone through the "getting connected" document and I can confirm that the network setup was successful.
I can confirm that AngryIP scan reported that the ip address on this board shows as connected on the wifi network.
I sent M122 from Pronterface
The results.```
[[language]]
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (4 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19 running on Duet WiFi 1.0
Board ID: 08DGM-95BNL-MGPSJ-6J1DG-3S46N-TKY7W
Static ram used: 21176
Dynamic ram used: 95936
Recycled dynamic ram: 1672
Stack ram used: 4008 current, 4956 maximum
Never used ram: 7332
Last reset 00:07:43 ago, cause: power up
Last software reset reason: not available
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 30.7, current 36.0, max 36.3
Supply voltage: min 12.1, current 12.1, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill
Driver 1: standstill
Driver 2: standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.009644; fastest: 0.000034
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19
WiFi MAC address 2c:3a:e8:0b:07:d2
WiFi Vcc 3.10, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 38712
WiFi IP address 192.168.2.27
WiFi signal strength -65dBm
HTTP sessions: 0 of 8
Socket states: 0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

I don't know what the free file reference means, but it clearly states in the diagnostics that the memory card is mounted and accessible at 20mb/sec```
[[language]]

SENDING:M21
SDHC card mounted in slot 0, capacity 3.64Gb

```I put all the .bin files into the /sys folder.

M997 S0 indicates file not found

If I put the IP address in my browser, it comes back stating that the IP address cannot be found

If I press the memory card icon on the duetwifi, no files are displayed on SD0 or SD 1 and I get the error 1 message

If I look on console there is no message indicating an attempt to initialise SD Card 0\. It does report that attempting to initialize SD Card 1 failed.

What if I put all the files on the type of memory card that is supported on the PanelDue. Is that the SD Card 1 port? Can I update the board from there? Can I use that instead of Card 0? so that I can use the printer?

dc42

Can you show us a listing of the files in the /sys folder?

If I put the IP address in my browser, it comes back stating that the IP address cannot be found

That's the odd bit. Looks like there is a communication issue between the Duet and your router. Here are some things that may help:

1. Try rebooting your router. This has worked for a few people.

2. Try changing channel on your router. Feedback from some some users suggests that channel 6 works better than channel 1.

3. Try setting a static IP address in the M587 command. First check on your router admin page that no other device is using that IP address.

TimVukman

https://timvukman-rogers.tinytake.com/sf/MjI2ODA4MV82OTgzMTYy

TimVukman

I will reboot the router
This channel works fine for the other duet card.

dc42

@TimVukman:

I will reboot the router
This channel works fine for the other duet card.

That's even more odd!

TimVukman

No go. Router rebooted. Can't connect to the new duet card.
Can connect to the old duet card no problem

Oddly enough my panelDue is displaying My Duet when it was displaying Tevo Tarantula earlier. It's not showing on AngryIP now either, so maybe it's signal strength?

Maybe I'll just shut it all down and give up until tomorrow

Tomorrow I might swap memory cards between the two printers. I won't turn on the printer, just connect to the board via USB and see if I can see anything different.

I guess I could move the PanelDue to the other board and see if it reads anything on the card that is currently in it.

If I'm careful moving things around, I might be able to isolate what is actually working and what is not.

TimVukman

It's a new day here, so let's get this sorted out once and for all.

I have not turned on this printer yet today.
I am connected via USB to the main board.
PanelDue Says My Duet in the top line
Console Says Connected

Pronterface connected and printer online
M552 from Pronterface says wifi module is disabled

M552 S0 Wifi Module is Started

M587 shows my network in remembered networks (also shows TNCAP2FCC19 which I know nothing about?)

M552 S1 show wifi module is connected to correct network with correct IP address.

AngryIP scanner hit the address in 11ms and returned the network address for the card.

PanelDue console reflects wifi module started and wifi module connected to access point with correct wifi name and correct ip address.

This is the document I have been following. What to do next for version 1.19 of the firmware says TODO
I have been trying to install the latest version of firmware so that it is the same version as my other Duet Card since I can't seem to get past this point.

I have entered my IP address in the browser and it appears that I am connecting today, but I am not getting the DWF interface screen in my browser. I am not getting an error message saying that it could not connect or that the address is unknown

[[language]]
https://duet3d.com/wiki/Getting_connected_to_the_Duet_WiFi

Something is different this morning.

I disconnected and reconnected the USB and when the board booted this time, it automatically went out and connected to the wifi network

I am also reading Tevo Tarantula in the red bar on the top of the PanelDue.

The only way for that to change would be that my config.g file was read, because that it where the printer name is defined. If it did not read config.g, the panel would say My Duet.

Now when I enter M997 S0, from Pronterface, I get an error message that says.
Error: In-application programming binary "iap4e.bin" not found which is true. That file is not on my memory card.

The iap files are not listed in the current firmware files on github for version 1.20

I copied the two files from the version 1.19 firmware on the same page. Is that ok??

Now I am getting Firmware binary "DuetWifiFirmware.bin" not found when I run M997 S0.

Obviously I am connecting to the network.
Obviously I am reading from the memory card.

M997 S0 reported DuetWifiFirmware.bin not found
M997 S1 installed successfully?

I checked the memory card and DuetWifiFirmware was no longer there? I copied it over again.
M997 S0 still fails
M122 reports

[[language]]
>>> m122
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.20 running on Duet WiFi 1.0
Board ID: 08DGM-95BNL-MGPSJ-6J1DG-3S46N-TKY7W
Static ram used: 15448
Dynamic ram used: 98544
Recycled dynamic ram: 696
Stack ram used: 3576 current, 4608 maximum
Never used ram: 11776
Last reset 00:08:18 ago, cause: power up
Last software reset details not available
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 52.3, current 52.9, max 55.8
Supply voltage: min 0.4, current 0.5, max 0.7, under voltage events: 0, over voltage events: 0
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 1757075559
Slowest main loop (seconds): 0.154149; fastest: 0.000101
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.20
WiFi MAC address 2c:3a:e8:0b:07:d2
WiFi Vcc 3.17, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 16480
WiFi IP address 192.168.2.27
WiFi signal strength -62dBm, reconnections 0, sleep mode modem
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

```Is it just me, or does this seem borderline flakey??????

whosrdaddy

after a successful firmware update, DuetWifiFirmware.bin will be deleted automatically.
Are you able to connect to DWC or not?