Auto tune cancelled because target temperature was not reached



  • Hi aidar

    Your english is fine and I understand what you are saying. Thanks for clearing up the heater numbering. Your response is appreciated.

    Tim



  • I made the changes I thought would fix the heater settings

    ; Heaters
    M305 P0 T100000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 0
    M143 H0 S120 ; Set temperature limit for bed heater 0 to 120C
    M305 P1 T100000 B4725 C0 R4700 ; Set thermistor + ADC parameters for heater 1
    M143 H1 S240 ; Set temperature limit for hotend heater 1 to 240C

    I received the same autotune failure message.

    Autotune ran for exactly 5 minutes, the nozzle temp reached 127.6 and it stopped because it took too long. I had set it to 200C.

    Can I change the time to 10 minutes instead of 5?

    Thanks,
    Tim


  • administrators

    What M303 command did you send? Perhaps you limited the PWM.



  • Thanks for your reply.

    I used
    M303 H1 S240

    which I got from
    https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control

    I changed S240 to S200 because I read that it's better to set the temperature for what you are going to use, or even set up different profiles based on the specific filament and the results of testing to identify the ideal temperature.

    I have never played with these settings before, or had a problem with the default.

    Should I run the configurator again? I would think I can just key in the settings, but obviously the tuning has to pass first.

    So, I'm kind of stuck

    Tim


  • administrators

    @timvukman said in Auto tune cancelled because target temperature was not reached:

    I used
    M303 H1 S240

    That's correct. It sounds as thought your hot end heater is under-powered, which is unusual. I suggest you check the connections. If you have a multimeter, measure the resistance of the heating element.



  • Hi:

    Fresh battery in the meter, I get 13.5 ohms.

    Tim

    This is what I bought for the conversion + the heated bed.
    1 x E3D Ceramic Cartridge Heater
    (Voltage, Wattage: 24V, 40W)
    1 x 24V Cooling Fan - Ball Bearing - 30mm x 30mm
    1 x 24V Cooling Fan - Ball Bearing - 40mm x 40mm
    1 x Power Supply - 24V, 400W



  • I am so sorry. I have to send a nasty note to my supplier. I ordered a 24V 400W power supply as noted above. After sending the resistance info I thought I should indicate what the duetwifi is showing.

    It shows 12.4V. It also says 12V 400W on the case.

    I will have to get them to send me a replacement that is 24V.

    I'll be away for a week, so I will get back to you.

    Tim



  • Hi:

    Autotune Passed

    Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 518C.
    Auto tune heater 1 completed in 333 sec
    Use M307 H1 to see the result, or M500 to save the result in config-override.g

    M307 H1
    Heater 1 model: gain 493.7, time constant 225.4, dead time 5.4, max PWM 1.00, calibration voltage 24.4, mode PID, inverted no, frequency default
    Computed PID parameters for setpoint change: P15.1, I0.434, D57.0
    Computed PID parameters for load change: P15

    Sorry to have wasted your time. I will be sure to check the voltage when the replacement supply arrives.

    Tim


  • administrators

    The value for B in M305 is for the thermistor beta value, not the heater model

    Try removing the current M307 valuer from your config-override.g and then running M303 again.

    also check out: https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control#Section_Troubleshooting_auto_tuning


  • administrators

    @timvukman said in Auto tune cancelled because target temperature was not reached:

    Hi:

    Autotune Passed

    Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 518C.
    Auto tune heater 1 completed in 333 sec
    Use M307 H1 to see the result, or M500 to save the result in config-override.g

    M307 H1
    Heater 1 model: gain 493.7, time constant 225.4, dead time 5.4, max PWM 1.00, calibration voltage 24.4, mode PID, inverted no, frequency default
    Computed PID parameters for setpoint change: P15.1, I0.434, D57.0
    Computed PID parameters for load change: P15

    Sorry to have wasted your time. I will be sure to check the voltage when the replacement supply arrives.

    Tim

    I'm glad you solved it! I presume you reverted to the 12V heater cartridge.


 

Looks like your connection to Duet3D was lost, please wait while we try to reconnect.