Firmware Name: RepRapFirmware for Duet WiFi and Duet Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 1.21RC2 (2018-02-15 build 2)
WiFi Server Version: 1.21RC2
Web Interface Version: 1.20

When i upload a file that is named fooprint(2).gcode and want to print the file it will say file does not exist
Error: M32: GCode file "0:/gcodes/26mmgauntbaseV2.gcode" not found
10:04:14 PMM32 0:/gcodes/26mmgauntbaseV2(2).gcode
any chance you might have a look into that?

this version made the wifi module much more stable i still get ocassional disconnects but im always able to reconnect

Thanks a lot

sorry for hijacking this happens with Chrome Firefox and even with Edge

Runningits FW RC2
Wifi Beta10 i believe
and RC3 Webclient

I have the same Issue everything is ok but when i Calibrate i cannot connect to my Printer but im able to print though i cannot see the status nor reconnect to the printer.

@dc42:

@Gosu:

i updated from RC1 to RC2 then it stopped running with wifi and i used the new www file to fix the problem

now i can only control my printer via wifi for 5 minutes(with constant disconnects) and i was able to start a print
but the printer stopped beeing able to connect via webhost
only seldomly beeing able to connect

i would love to post my current version but it wont let me connect
its FW RC2
Wifi Beta10 i believe
and RC3 Webclient

Did you install DuetWiFiFirmware twice as recommended in the upgrade notes?

Yes i did and it works for a few seconds but i just connected wanted to set the temp then it disconnected and doesnt let me connect again

6:34:03 PMDisconnected.
6:32:41 PMConnection established!
6:32:40 PMPage Load complete!

I restarted the Duet and i was able to connect
then i disconnected while i was doing autocalibration

Again another restart!

this time i was quick !!!

6:46:57 PMEndstop adjustments X-0.26 Y0.61 Z-0.35, tilt X0.00% Y0.00%
Diagonal 291.060, delta radius 144.058, homed height 380.282, bed radius 200.0, X 0.829°, Y 0.399°, Z 0.000°

File 0:/gcodes/Step_1_-Single-Wall_Box.gcode selected for printing
6:46:56 PMM32 0:/gcodes/Step_1-_Single-Wall_Box.gcode
Calibrated 6 factors using 13 points, deviation before 0.248 after 0.105
6:45:41 PMConnection established!
6:45:41 PMPage Load complete!

The Print itself looks good but i cannot connect with the printer so i cannot see the status nor do anything with my printer except restarting or waiting for the print to finish..

after the restart it works for a certain ammount of time
i have restarted the device and reconnected
then i have set bed temperature 1 minute later it was dead and didnt respond to pings while still heating to temperature and beeing responsive with a cable and pronterface

the disconnects are making using the printer almost impossible

I reinstalled the Firmwares
I started by reuploading both bins on the SD connecting the Printer with Pronterface and then Installing the Firmware first then the Wifiserver

it worked for 5 minutes then the same problems appeared

i updated from RC1 to RC2 then it stopped running with wifi and i used the new www file to fix the problem

now i can only control my printer via wifi for 5 minutes(with constant disconnects) and i was able to start a print
but the printer stopped beeing able to connect via webhost
only seldomly beeing able to connect

i would love to post my current version but it wont let me connect
its FW RC2
Wifi Beta10 i believe
and RC3 Webclient

Yes thats what im saying its very hard to get a low deviation i have a heavy aluminium heatbed wich makes triggering a little bit delayed but after adjusting trigger heights its perfect and i can print whatever i want on my rostock max v2 310 mm build plate just g32 before each print and swoosh

i have 0.100 deviation and i print very high quality the limits are the sensors you use i run duet with FSR and since i have a filaprint everything sticks and the first layer looks like its molded just try to print the best deviation i have achieved was 0.078 and it makes literally no difference to me even when using 0.05 layers i would say try a few prints and see what you can do