@dc42 @droftarts

Hello,
I have taken your advice and reduced V to 100. I also had to change other parameters in some way, namely the current and the M915 command. I find that S12 and H300 works best for me on x and y axis. Thank you very much for all your help.

video_homing.mp4

Hello, I have already opened a similar topic on general discussion, but thought it might be beneficial to ask here. I was following open5x project from Freddie Hong. I am kind of new to printing, and I am currently having problems with homing the axes without sensors. I am using Duet 3 Mini 5+, along with Duet 2+ expansion. I have also attached a video to show the problem with what the motor on x axis does when homed. Has anybody managed to make it work with such a setup?

@dc42

Hello,

I have tried changing the V parameter from 500 to 2000. Any value for feed-rate returns the same errors, either too slow or too fast.

I have also attached a video of the issue. This was an experiment I did using previous firmware but with the same type of setup. Changing parameter values didn't change the output.

video_homing.mp4

@jay_s_uk @dc42

That is right about the firmware, I corrected that. I tried testing the new version, just moving the motors around a little bit through the console with G1 command, and homing X axis alone. The error messages report that the moves are either too slow, or too fast for driver x to detect stall ( full error text: Error: G1: move is too slow for driver 0 to detect stall (increase speed or Tcoolthrs , or Error: G1: move is too fast for driver 0 to detect stall (reduce speed or Tpwmthrs) ). For example, I get too slow for feed rate 2000, but too fast for just a slight change such as 2100.

@dc42

Hello,

I have tried updating to beta version, but I get a warning about incompatibility. About the stealthchop mode, I put the settings in config. Wouldn't changing driver settings at the beginning and end of home files require restarting?

These are my files.
config:

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"open5x" ; set hostname

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Network
M552 P0.0.0.0 S1 ; configure Ethernet adapter 
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0.0 S0 D3 V2000                  
M569 P0.1 S0 D3 V2000                 
M569 P0.2 S0 D3 V2000                   
M569 P0.3 S0 D3 V2000 
M569 P0.4 S1 D3 V2000            
M569 P0.5 S0 D3 V2000      
M569 P0.6 S0 D3 V2000    

; Motor Idle Current Reduction
M906 I30 
M84 S30

; Axes
M584 X0.0 Y0.1 Z0.2:0.3 E0.4 A0.5 B0.6                                       
M350 X16 Y16 Z16 E32 A16 B16 I1                                          
M906 X620.00 Y620.00 Z560.00 E700.00 A1300.00 B1300.00 I10           
M92 X100.00 Y100.00 Z400.00 E280.00 
M92 A26.667 
M92 B35.556 

M566 X240.00 Y240.00 Z12.00 E270.00 A480.00 B480.00 P1 
M203 X12000.00 Y12000.00 Z750.00 E1500.00 A5000.00 B12000.00  	  
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 A1000.00 B1000.00   	

M208 X0:250   Y-92.3:50  Z-125:1 A-200:200 B-12000:12000    
M564 H0

; Endstops
M574 X1 S3
M574 Y1 S3
M574 Z1 S3

M915 X S3 F0 H200 R1		           
M915 Y S3 F0 H200 R1		         
M915 Z S3 F0 H200 R1		          

; Z-Probe (manual)
M558 P0 H15 F120 T6000      

M140 H-1 ; Disable heated bed

; Filament Sensor Port and Loading Feature ON
M950 J1 C"io1.in"
M581 P1 T2 S0 R0

; HotEnd Heaters and Thermistor HotEnd           
M308 S1 P"temp2" Y"thermistor" T100000 B4725 R4700 

M950 H1 C"out1" T1					
M307 H1 A306.9 C115.4 D4.0 V23.8 B0		
M143 H1 S285                         
M302 S185 R185

; Fans
M950 F1 C"io2.out" Q250			
M106 P1 T85 S0 H1                
M950 F0 C"io3.out" Q250
M106 P0 S0 H-1          

; Tools
M563 P0 D0 H1 F0                        
G10 P0 X0 Y0 Z0            
G10 P0 R0 S0

homeall:

M915 X S10 F0 H200 R1		           
M915 Y S10 F0 H200 R1		       
M913 X50 Y50 Z50 

G91     ;relative

G1 H2 Z10 F800   ;move Z up    
G1 H1 X-255 F2400   ;move X to endstop
G1 H1 Y-215 F2400   ;move Y to endstop

G1 H1 Z205 F1800    ;move Z to endstop

G90     ;absolute

M913 X100 Y100 Z100     ;restore
M915 X S3 F0 H200 R1		               
M915 Y S3 F0 H200 R1

Hello, I have been working on a Prusa MK3S upgrade based on the open5x repository on github, but I am having problems with sensorless homing of xyz axes. The difference to the repository is that I am using Duet 3 Mini 5+ board. I tried a number of different parameter combinations, but I cannot get it work. The motor hits the edge and just keeps on going, it doesn't recognize the edge of the printer. I tried changing current, speed, sensitivity, acceleration, jerk, the StealthChop settings. Where can I find some additional guidance regarding the parameters which enable sensorless homing?