@droftarts the old and new chip were both the 07S..
This is the chip I used. (Never mind can’t post links.. it was a 2 pack off Amazon for $7.48)
It looks identical to the old one. But I’m definitely not an electronics expert. I appreciate all your all’s replies.
Hey there, so I was given a Vivedino Troodon 1.0 that uses a Troodon specific board that runs on RRF.. so I know this doesn't apply specifically to Duet. Hoping maybe you all can provide some help though.
I had to remove the old wifi chip, an ESP-07S chip. I had to replace it because the pad where the antenna connection (U.FL) broke off.
I think I got the new chip soldered in correctly, but now I'm just getting this from YAT:
Any guidance or advice would be great! I was going to link the controller on their website but I can't post links yet... thanks.
@droftarts Yeah buddy! I'm connected, did that M552 S0, M587 and set up network and I'm now connected. I should've tried that before commenting again. Thanks again for your all's help! It seems really obvious now that I have to upload the firmware to the new wifi chip 
lol
Thanks for helping me out! We can close this issue 
@droftarts Ahh yeah, that made it much better to read.
I think we're all good, but here's my M122
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04RC1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86T-982LP
Used output buffers: 1 of 24 (12 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 94268 of which 296 recycled
Exception stack ram used: 320
Never used ram: 10508
Tasks: NETWORK(ready,476) HEAT(blocked,1236) DUEX(suspended,156) MAIN(running,3796) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:12:52 ago, cause: power up
Last software reset at 2024-11-06 19:50, reason: User, spinning module GCodes, available RAM 10288 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 21.6, current 22.0, max 22.2
Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available
Date/time: 2025-03-22 08:41:05
Cache data hit count 2234544828
Slowest loop: 1.72ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 200.34ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
@droftarts Also thanks for the upvotes! Totally understand the rule
@droftarts Yeah buddy! I'm connected, did that M552 S0, M587 and set up network and I'm now connected. I should've tried that before commenting again. Thanks again for your all's help! It seems really obvious now that I have to upload the firmware to the new wifi chip lol
Thanks for helping me out! We can close this issue
@jay_s_uk That was definitely the first problem!
Here's what I'm getting now..
@droftarts the old and new chip were both the 07S..
This is the chip I used. (Never mind can’t post links.. it was a 2 pack off Amazon for $7.48)
It looks identical to the old one. But I’m definitely not an electronics expert. I appreciate all your all’s replies.
@jay_s_uk I have not, I’m going to try that right now!
Hey there, so I was given a Vivedino Troodon 1.0 that uses a Troodon specific board that runs on RRF.. so I know this doesn't apply specifically to Duet. Hoping maybe you all can provide some help though.
I had to remove the old wifi chip, an ESP-07S chip. I had to replace it because the pad where the antenna connection (U.FL) broke off.
I think I got the new chip soldered in correctly, but now I'm just getting this from YAT:
Any guidance or advice would be great! I was going to link the controller on their website but I can't post links yet... thanks.