Better now?

I try another cable and everything is working now

Thank you!

Better now?

On my Duet wifi, I'm not able to setup network. No serial COM is detected when I plug it in usb on diferent computer, diferent cable or usb port.

I try something but I don't undertand why my try is not working. I use this config.g:

M550 RickyBuilt3D                             ; Set machine name
M552 S0                                       ;stop wifi
G4 P10000		                      ;pause
M587 S"SSID" P"PASSWORD"                      ; set network
G4 P10000				      ;pause
M552 S1                                       ;start wifi
M586 P0 S1                                    ; Enable HTTP


;Heaters

M307 H0 B0 S1.00                                ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3950 C0 R4700                  ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                    ; Set temperature limit for heater 0 to 120C
M140 S60				        ;Bed temp 60

When I use it my bed start to heat at the end and show me that the file is loaded

Thank you for fast anwser.

For my slow homing I found the problem in my cura "start gcode"

I got a CR-10, I try to make my config files and still not be able to correct somes things...

My cr-10 have only this modifications:

the X axes inverted
BMG Extruder
3 wires limits switchs (VCC,Ground,Signal)
Duet WiFi board

First problem (I don't make to much search on this one)

My X homing movement is inverted and it just move alittle and stop with homing done. It does't not hit any limit switch

2nd
My manual homing in z is perfect even with home all. When I start my program I can't change Z speed for homing and retract inprint Z movement.

Here's is my config.g code

Thank you

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up

; General preferences
G90                                     ; Send absolute coordinates...
M83                                     ; ...but relative extruder moves

; Network
M550 CR-10	                       ; Set machine name
M552 S1                                 ; Enable network
M586 P0 S1                              ; Enable HTTP
M586 P1 S0                              ; Disable FTP
M586 P2 S0                              ; Disable Telnet

; Drives
M569 P0 S1                              ; Drive 0 (X) goes forwards
M569 P1 S0                              ; Drive 1 (Y) goes forwards
M569 P2 S1                              ; Drive 2 (Z1) goes backwards
M569 P3 S1                              ; Drive 3 (E) goes forwards
M584 X0 Y1 Z2 E3			; Driver 0=X, 1=Y, 2=Z, 3=E
M350 X16 Y16 Z16 E16 I1                 ; Configure micro-stepping with interpolation
M92 X80 Y80 Z400 E460                   ; Set steps per mm
M566 X1200 Y1200 Z1800 E300              ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1800 E1500           ; Set maximum speeds (mm/min)
M201 X500 Y500 Z500 E500              ; Set accelerations (mm/s^2)
M906 X525 Y600 Z675 E600 I30            ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; Set axis minima
M208 X300 Y300 Z400 S0                  ; Set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                           ; Set active high endstops

; Z-Probe
M210 X1500 Y1500 Z1800			;Set the feedrates used for homing to the values specified in mm per minute.

; Heaters
M307 H0 B0 S1.00                        ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3950 C0 R4700          ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                            ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700      ; Set thermistor + ADC parameters for heater 1
M307 H1 A493.9 C176.8 D4.6 S1.00 V23.9 B0     ; E3D V6 Hotend Calibration
M143 H1 S280                            ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 H-1                       ; Part Cooling Fan. Manual control.
M106 P1 T45 H1                          ; Hotend Heatsink Fan. Thermostatic control, max RPM at 45C.
M106 P2 T25:65 H100:101:102		; Duet Electronics Fan. Thermostatic control, turn on at 25C, max RPM at 65C.

; Tools
M563 P0 D0 H1                           ; Define tool 0
G10 P0 X0 Y0 Z0                         ; Set tool 0 axis offsets
G10 P0 R0 S0                            ; Set initial tool 0 active and standby temperatures to 0C

; Miscellaneous
T0                                      ; Select first tool