Got it!!
Did it with bossa.
Thanks.

Thanks a lot for your help.
I think I'm ok on rpi, I also copy my backup system folder to rpi but the error persist.

echo M997 | sudo /opt/dsf/bin/CodeConsole

Don't work:

Unhandled exception. System.Net.Internals.SocketExceptionFactory+ExtendedSocketException (99): Cannot assign requested address /var/run/dsf/dcs.sock
   at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
   at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
   at DuetAPIClient.BaseConnection.Connect(ClientInitMessage initMessage, String socketPath, CancellationToken cancellationToken) in /home/christian/Duet3D/DuetSoftwareFramework/src/DuetAPIClient/BaseConnection.cs:line 98
   at CodeConsole.Program.Main(String[] args) in /home/christian/Duet3D/DuetSoftwareFramework/src/CodeConsole/Program.cs:line 44
   at CodeConsole.Program.<Main>(String[] args)
Aborted

I never had to flash the board till now.

Thanks a lot.

Hi,
I tried 3.2beta2 on Duet3 with Rpi but nothing really works for me. I was unable to make a print, the Z axis moves very slowly, and the start of the print is not done correctly. The head and the bed seem to go their own way .... until the bed hits the head.

I tried downgrading with:

apt-get install duetsoftwareframework=3.1.1 duetcontrolserver=3.1.1 duetsd=1.0.6 duettools=3.1.1 duetwebserver=3.1.0 duetwebcontrol=3.1.1 reprapfirmware=3.1.1-1 duetruntime=3.1.1

DuetSoftwareFramework goes wrong:

Oct 17 17:06:52 raspiduet systemd[1]: Started Duet Control Server.
Oct 17 17:06:53 raspiduet DuetControlServer[1482]: Duet Control Server v3.1.1
Oct 17 17:06:53 raspiduet DuetControlServer[1482]: Written by Christian Hammacher for Duet3D
Oct 17 17:06:53 raspiduet DuetControlServer[1482]: Licensed under the terms of the GNU Public License Version 3
Oct 17 17:06:54 raspiduet DuetControlServer[1482]: [info] Settings loaded
Oct 17 17:06:55 raspiduet DuetControlServer[1482]: [info] Environment initialized
Oct 17 17:06:55 raspiduet DuetControlServer[1482]: [warn] Kernel SPI buffer size is smaller than RepRapFirmware buffer size (4096 configured vs 8192 required)
Oct 17 17:06:55 raspiduet DuetControlServer[1482]: [fatal] Could not connect to Duet (Invalid protocol version 3)
log file: ize is smaller than RepRapFirmware buffer size

How can I downgrade to 3.1.1 correctly?
Thanks

Thanks deckingman, I see it now.

Hello,
I'm trying to change the extruder with Bondtech QR and
I messed up with the motor cable and I don't think I connected the pins correctly.
It makes a bad noise and the firmware tells me:
"Warning: motor phase A may be disconnected reported by driver (s) 3."
The motor moves in the exact direction. Ho controllato se i connettori fanno contatto e mi sembra OK.

What can I have done?

Thanks.

Thanks a lot dc42!!!

Hello,
please I need help to connect the Noctua NF-A4x10 PWM fan to the Duet 3 mainboard.

Noctua NF-A4x10 PWM
Black = GND
Yellow = + 12V
Green = RPM speed Signal
Blue = PWM Signal

Duet 3:
OUT X GND
V_OUTLC1
outx.tach
outx

Thanks.

I believe I will use DuetSocketFramework but I have yet to start. I wasted too much time installing qt on windows!
So the only solution is to buy a Duet card to do software development, it seems cheap!
I was hoping there was a simulator or something like that at least for the main functions.
Thank you.

I have finished installing the various development environments and would like to start developing the GUI. Is there any way to simulate the duet 3 card or should I always have the raspberry connected to the duet3 card?
Thank you.

@resam sorry me for delay.
I can't do anything at the moment, I disassembled the printer to finish some works with duet 3