Ah you got me wrong : D

The other two colors are loaded until the nozzle, so the Bowden tube is not open. I did this mistake once and my ptfe clogged. This will not happen again : D

Ah thanks, good to know!

I'm actually printing with only one color trough the diamond until the parameters are set. I recognized that the other two are already clogged ^^will try to fix that later

Yeah, this is what the first prints look like : )

I'm actually fine tuning the parameters, gets better and better, thanks guys!

I don't really know the problem with the HomeAll.g, it was created automatically with these reprap config thingi.

I copied the homeX Y and Z in the homeAll, know that works.

Later when I'm home again, I'll try
At the moment I'm on an expo in Stuttgart Germany

Yeah, so this is what the first print looks like

I guess I need to check the settings in cura ^^

https://youtu.be/5rHifXGffac

[SOLVED]

Hey guys, thanks for commenting : )

yes, i'm using the actual 1.18.1 firmware

so the first few lines of my gcode look like the following, but it still shuts down the heaters when i start the print.
Maybe the the order is the problem?

i also included G82 in the Config file and commented out the G90, was this the right action?

edit: the only output im getting on the gcode console is:
18:32:28
M32 1stTrinity.gcode
File 1stTrinity.gcode selected for printing

edit2: when i start the print, the only thing happens is moving the bed 10mm down, and then shut off the heaters. it somehow skips the homing and probing

edit3: so i found a new problem which brings us more to thee root of the evil ^^
when i home the axis individually, everythings fine. when i hit homeall.g, it shuts down the heaters as well, i guess the problem is here. scroll down for the homeall.g : )

edit4: okey guys, i solved the problem
the issue was the HomeAll.G, i corrected it, now it does the probe points and prints as it should, thanks for the support! it's my very first print with the duet, i will post some pictures here : )

---

;FLAVOR:RepRap(Volumetric)
;TIME:2430
;Generated with Cura_SteamEngine 2.5.0
T0
M190 S60
M104 S200
M109 S200
G28 ;Home
G1 Z15.0 F6000 ;Move the platform down 15mm
G29
;Prime the extruder
G92 E0
G1 F200 E3
G92 E0
;LAYER_COUNT:59
;LAYER:0
M107
G0 F3600 X99.433 Y106.157 Z0.3
;TYPE:SKIRT
G1 F1800 X100.016 Y105.626 E0.09463

---

Homeall.G

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool on Mon May 15 2017 04:27:52 GMT+0200

; Relative positioning
G91

; Lift Z
G1 Z10 F6000

; Course home X or Y
G1 X-255 F1800 S1
G1 Y-255 F1800 S1
; Course home X
G1 X-255
; Course home Y
G1 Y-255

: Move away from the endstops
G1 X5 Y5 F6000

; Fine home X
G1 X-255 F360 S1
; Fine home Y
G1 Y-255 S1

; Move Z down until the switch triggers
G1 Z-405 F1800 S1

; Absolute positioning
G90

; Tell the firmware where we are
G92 Z0

; Uncomment the following line to lift the nozzle after probing
G1 Z0 F100

; Relative positioning
G91

; Lift Z
G1 Z0 F6000

; Move Z down until the switch triggers
G1 Z-405 F1800 S1

; Absolute positioning
G90

; Tell the firmware where we are
G92 Z0

; Uncomment the following line to lift the nozzle after probing
G1 Z0 F100

Hey folks,

My DIY printer is already finished, today I hooked up the RepRap diamond Hotend and adjusted the bed.

Everything works so far, my only problem is the first print!

I tried the example Gcode EscherLizard, but it ignores the bed compensation. Manually including G28 (Homing) and G29 after G90 creates the issue that the print is "@100%" right after start and shuts down the heaters.

Sliced objects via Cura also don't work, same problems with G28/G29

Is there any special way to slice objects for the duet?

At that time I started the post, i did not have any adjusting possibilities for the bed

Now I installed a 3Point system for Pre-Adjusting the printbed

Actually I'm fighting with the first print, somehow it shuts down the heaters when I start a print, but that's another Story

The problem in this thread is [Solved]

Yeah, for safety I installed the probe higher so it would trigger before the nozzle could crash in the bed and I can react

Now it's calibrated better and I think tomorrow I'll start the first print

Again, thanks guys!

Updating the firmware from 1.15b to 1.18.1 solved the problem!

Here is a video! Thank you guys, love you all

Is there any way to Donate for Duet or the forums? ?
https://youtu.be/nVCJJLAbHAA