@droftarts I ordered a multimeter so I wont be able to check right now.
@peter247 I tried to do that as well with no luck. I also re-crimped them to see if I messed up, but no luck.
@Phaedrux Thank you for the suggestion, I have downloaded it and uploaded it, but still didn't get any response from the BLTouch. Hopefully when the multimeter comes I will finally have my answer.

Thank you for your reply!!!
Everything you asked for can be found below.

config.g

 ; Configuration file for Duet WiFi (firmware version 1.21)
 ; executed by the firmware on start-up
 ;
 ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 02 2020 18:51:18 GMT-0400 (Eastern Daylight Time)
 
 ; General preferences
 G90                                                ; send absolute coordinates...
 M83                                                ; ...but relative extruder moves
 M550 P"BLV mgn Cube"                               ; set printer name
 M667 S1                                            ; select CoreXY mode
 
 ; Network
 M552 S1                                            ; enable network
 M586 P0 S1                                         ; enable HTTP
 M586 P1 S0                                         ; disable FTP
 M586 P2 S0                                         ; disable Telnet
 
 ; Drives
 M569 P0 S1                                         ; physical drive 0 goes forwards
 M569 P1 S1                                         ; physical drive 1 goes forwards
 M569 P2 S1                                         ; physical drive 2 goes forwards
 M569 P3 S0                                         ; physical drive 3 goes backwards
 M584 X0 Y1 Z2 E3                                   ; set drive mapping
 M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
 M92 X80.00 Y80.00 Z4000.00 E420.00                 ; set steps per mm
 M566 X720.00 Y720.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
 M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
 M201 X500.00 Y500.00 Z250.00 E250.00               ; set accelerations (mm/s^2)
 M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
 M84 S30                                            ; Set idle timeout
 
 ; Axis Limits
 M208 X0 Y0 Z0 S1                                   ; set axis minima
 M208 X340 Y350 Z350 S0                             ; set axis maxima
 
 ; Endstops
 M574 X1 Y1 S1                                      ; set active high endstops
 M574 Z1 S2                                         ; set endstops controlled by probe
 
 ; Z-Probe
 M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch
 M558 P9 H5 F120 T6000                              ; set Z probe type to bltouch and the dive height + speeds
 G31 P25 X30 Y24 Z0                                 ; set Z probe trigger value, offset and trigger height
 M556 S50 X0 Y0 Z0                                  ; set orthogonal axis compensation parameters
 M557 X15:285 Y15:285 S20                           ; define mesh grid
 
 ; Heaters
 M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
 M143 H0 S100                                       ; set temperature limit for heater 0 to 100C
 M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
 M143 H1 S260                                       ; set temperature limit for heater 1 to 260C
 
 ; Fans
 M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
 M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
 M106 P2 S1 I0 F500 H1 T45                          ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
 
 ; Tools
 M563 P0 D0 H1 F0                                   ; define tool 0
 G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
 G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C
 
 ; Custom settings are not defined
 
 ; Miscellaneous
 M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

homeall.g

 ; homeall.g
 ; called to home all axes
 ;
 ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 02 2020 18:52:45 GMT-0400 (Eastern Daylight Time)
 G91                     ; relative positioning
 G1 S2 Z5 F6000          ; lift Z relative to current position
 G1 S1 X-345 Y-355 F1800 ; move quickly to X or Y endstop and stop there (first pass)
 G1 S1 X-345             ; home X axis
 G1 S1 Y-355             ; home Y axis
 G1 X5 Y5 F6000          ; go back a few mm
 G1 S1 X-345 F360        ; move slowly to X axis endstop once more (second pass)
 G1 S1 Y-355             ; then move slowly to Y axis endstop
 G90                     ; absolute positioning
 G1 X-15 Y-9 F6000       ; go to first bed probe point and home Z
 G30                     ; home Z by probing the bed
 
 ; Uncomment the following lines to lift Z after probing
 ;G91                    ; relative positioning
 ;G1 Z5 F100             ; lift Z relative to current position
 ;G90                    ; absolute positioning

deployprobe.g

 ; called to deploy a physical Z probe
 ;
 ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 02 2020 18:53:16 GMT-0400 (Eastern Daylight Time)
 M280 P3 S10 I1 ; deploy BLTouch

retractprobe.g

 ; retractprobe.g
 ; called to retract a physical Z probe
 ;
 ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 02 2020 18:55:09 GMT-0400 (Eastern Daylight Time)
 M280 P3 S90 I1 ; retract BLTouch

m115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.0(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-06-05b3

I have been working on a Printer build and got it to work.... more or less. I would really like to use a BLTouch with it but the touch is not lighting up at all. When I configured it, I followed the guide here
[https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Duet_2_WiFi_Ethernet_without_a_Duex_2_or_Duex_5_expansion_board].
I wired it the exact way and had used a different cords (Long and Short) and different touchs. When I configured using the online reprap configuration tool, since I am using the 8th pin for Heater 3, I set it to use the E2 channel for the servo control channel.
Also any of the prob commands return as successful.

If anyone has more info, please Let me know. Thank you all.