@fcwilt
Yes, the wiring to the BLTouch runs alongside the extruder stepper motor's cable in the same cable chain. (it was quite tight before now I bought a wider one because the cables were a bit too much near).
this is how I configured the commands.
M558 P9 C"^zprobe.in" H5 F120 T6000
G31 P500 X0 Y-39 Z0.8
could anyone help me? I would still like to understand why I had this problem. I waited for an answer but no one answered me
@phaedrux yes, I saw it multiple times now.
from what I remember the probe looks like it's triggering ok.
Ah yes and the problem persists even changing from a duet 2 maestro (that was mounted before) to a duet 2 wifi
Hello there,
I am writing because sometimes my duet 2 wifi with RepRap firmware version 3.3 goes a bit crazy sometimes.
Usually everything works perfectly, but sometimes happens one of these 2 things:
1)The printer stops the bed mesh compensation in the middle of the procedure and with the probe down starts to print (touching the bed), once it even went out of the bed bending a bit the bl touch probe.
2)The bed mesh compensation looks like it worked ok but starts to print 3mm higher or sometimes lower than it should.
I don't understand what is wrong with it, maybe the bl touch? I think it's connected to that but for a lot of months it worked ok without any problem.
@jay_s_uk === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N85S4-7JTD6-3SS6L-KA8ZQ
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 74132 of which 244 recycled
Never used RAM 16164, free system stack 184 words
Tasks: NETWORK(ready,13.1%,257) HEAT(delaying,0.0%,386) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,0.5%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:03:46 ago, cause: power up
Last software reset at 2021-09-18 15:05, reason: User, GCodes spinning, available RAM 13308, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 25.1, current 32.7, max 32.7
Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-09-20 10:37:31
Cache data hit count 4294967295
Slowest loop: 6.10ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.62ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
@dc42 firmware is the latest stable version, and the same should be with wifi module firmware and DWC. How can i control wifi module and dwc version?
Hello there,
While setting up my duet 2 WiFi 90% of the times after an emergency reboot I get a white page instead of dwc.
Than after 30 minutes I can see DWC again.
What can I do?
Thanks