@gixxerfast man, I never thought I would get this much help at setting up my printer and learning what's going on. I am very appreciative
Best posts made by frnknstn
-
RE: z probe help if possibleposted in IR Height Sensor
Latest posts made by frnknstn
-
proboingposted in Tuning and tweaking
voron 2,,my printer is probing then hitting the z switch. is it suppose to register the z switch then probe the gantry based off that?
-
RE: Trigger height is not right, still hitting bed when probingposted in Tuning and tweaking
@stephen6309 just noticed i dont even have G31 in my config
code_text ```; Configuration file for Duet WiFi (firmware version 2.03 or newer) ; executed by the firmware on start-up ; General preferences M111 S0 ; Debugging off G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M555 P2 ; Set firmware compatibility to look like Marlin M575 P1 B57600 S1 ; Comms parameters for PanelDue M564 S1 H1 ; Forbid axis movements when not homed ; General setup M669 K1 ; Select CoreXY mode (2.03 and up) ; Network M550 P"Duet3" ; Set machine name M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP (for DWC) M586 P1 S1 ; Enable FTP (for remote backups) M586 P2 S0 ; Disable Telnet ; --- drive map --- ; _______ ; | 6 | 7 | ; | ----- | ; | 5 | 8 | ; ------- ; front ; Drive directions M569 P0.0 S0 V0 ; Drive 0: E Axis M569 P0.1 S0 V0 ; Drive 1: Z-LeftFront Axis M569 P0.2 S1 V0 ; Drive 2: Z-LeftRear Axis M569 P0.3 S0 V0 ; Drive 3: Z-RightRear Axis M569 P0.4 S1 V0 ; Drive 4: Z-RightFront Axis M569 P1.0 S1 V0 ; Drive 5: Expansion: B motor (X-axis) M569 P1.1 S1 V0 ; Motor mapping and steps per mm M584 X1.0 Y1.1 Z0.1:0.2:0.3:0.4 E0.0 M350 X16 Y16 Z16 I1 ; Use 1/16 microstepping with interpolation everywhere M350 E16 I1 ; no microstepping on the extruder M92 X80 Y80 Z400 ; Set XYZ steps per mm (1.8deg motors) ;M92 X160 Y160 Z800 ; Set XYZ steps per mm (0.9deg motors) M92 E404 ;417 was original - after tuning 405 was slightly over 100mm. Therefore, 404 ;M350 Z16 I0 ; disable Z interpolation ; Drive currents M906 X1200 Y1200 Z1200 E1000 ; XYZ and E current M906 I30 ; Idle current percentage M84 S120 ; Idle timeout ; Endstops M574 X2 S1 P"io0.in" ; X max active low endstop switch M574 Y2 S1 P"io1.in" ; Y max active low endstop switch ;M574 Z0 P"io3.in" ; zstop is free M208 X0 Y0 Z0 S1 ; Set axis minima M208 X400 Y300 Z230 S0 ; Set axis maxima ; Bed leveling ;M671 X-65:-65:265:265 Y-20:280:280:-20 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right) M671 X-65:-65:320:320 Y-20:350:350:-20 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right) M557 X50:200 Y50:200 S25 ; Define bed mesh grid (inductive probe, positions include the Z offset!) ; Accelerations and speed M98 P"/macros/print_scripts/speed_printing.g" ; Heaters M308 S0 P"temp_0" Y"thermistor" A"Bed" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out_0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 R0.173 C613.4 D2.91 S1.00 V24.1 ; set model parameters for heater 1 and use PID mode M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"temp_1" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out_1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.435 C159.6 D3.53 S1.00 V24.1 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 M950 F0 C"out7" Q100 M106 P0 C"Part Cooling" ;Side Fans ;M950 F5 C"duex.fan5" Q100; ;M950 F6 C"duex.fan6" Q100; ;M106 C"Electronics Bay"P5 T45:65 F50 H100:101:102 ; Electronics bay fan, turn on gradually if MCU is over 45C or any TMC driver is over temp ;M106 C"Electronics Bay"P6 T45:65 F50 H100:101:102 ; Electronics bay fan, turn on gradually if MCU is over 45C or any TMC driver is over temp ; Chamber temperature sensor via temperature daughterboard pins on Duex ;M305 S"Ambient" P104 X405 T21 ; Set DHT21 for chamber temp ;M305 S"Humidity [%]" P105 X455 T21 ; Set DHT21 for chamber humidity ; Disable unused heaters (so they are hidden on the PanelDue) ;M307 H2 A-1 C-1 D-1 ;M307 H3 A-1 C-1 D-1 ;M307 H4 A-1 C-1 D-1 ;M307 H5 A-1 C-1 D-1 ;M307 H6 A-1 C-1 D-1 ;M307 H7 A-1 C-1 D-1 ; Select inductive Z probe on powerup M98 P"/macros/print_scripts/activate_z_probe.g" ; Fans ; Fans M950 F0 C"out7" Q500 ; Parts cooling create fan 0 on pin out7 and set its frequency M106 P0 S0 H-1 M950 F1 C"out8" Q500 ; Extruder create fan 1 on pin out8 and set its frequency M106 P1 T45 H1 ; Tools M563 P0 D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Enable pressure advance ; 0.085 was damn near perfect. Slight blobbing. Upping to 0.087. M572 D0 S0.087 M501 ; load config-override.g T0 ; select tool 0 -
RE: Trigger height is not right, still hitting bed when probingposted in Tuning and tweaking
@stephen6309 i switched this and it is still the same. am i changing this in another macro? ```
code_text; P8: unfiltered ; C"io2.in": set pin to zprobe ; T18000: Move to probe points at 300mm/s ; F1200: Probing Speed: 20mm/s ; H5: Dive height: 5mm ; A5 S0.01: Perform up to 5 touches until change is below 0.01mm ; B1: Turn off heaters while probing M400 M558 P8 C"io2.in" H10 F1200 T18000 A5 S0.01 B1; set Z probe type to modulated and the dive height + speeds G31 P500 X0 Y25 Z0.757 ; inductive probe offset, not critical, only used for coarse homing G4 P200 -
Trigger height is not right, still hitting bed when probingposted in Tuning and tweaking
trying to get this trigger height correct. seems any adjustment im doing has no effect. Im assuming i am adjusting the wrong spot..
code_text ; Select inductive probe, OMRON TL-Q5MC2-Z ; P8: unfiltered ; C"io2.in": set pin to zprobe ; T18000: Move to probe points at 300mm/s ; F1200: Probing Speed: 20mm/s ; H5: Dive height: 5mm ; A5 S0.01: Perform up to 5 touches until change is below 0.01mm ; B1: Turn off heaters while probing M400 M558 P8 C"io2.in" H10 F1200 T18000 A5 S0.01 B1; set Z probe type to modulated and the dive height + speeds G31 P500 X0 Y25 Z-.757 ; inductive probe offset, not critical, only used for coarse homing G4 P200 -
RE: G28 Z error homing failedposted in Duet Web Control
@frnknstn i am trying to go by these and adjust them
-
RE: G28 Z error homing failedposted in Duet Web Control
@frnknstn ```
This is the homez; called to home the Z axis ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Apr 23 2020 19:55:13 GMT+0100 (British Summer Time) G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G90 ; absolute positioning G1 X50 Y50 F6000 ; go to first probe point G30 ; home Z by probing the bed ; Uncomment the following lines to lift Z after probing ;G91 ; relative positioning ;G1 Z5 F100 ; lift Z relative to current position ;G90 ; absolute positioningThis is the home all
; called to home all axes ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Apr 23 2020 19:55:13 GMT+0100 (British Summer Time) G91 ; relative positioning G1 H1 X-335 Y-335 ; move quickly to X or Y endstop and stop there (first pass) G1 X5 Z5 F6000 ; go back a few mm G1 H1 X-335 F360 ; move slowly to X axis endstop once more (second pass) G1 H1 Y-335 F360 ; move slowly to Y axis endstop once more (second pass) G1 X50 Y50 ; Move z probe over bed G1 H1 Z-405 ; then move slowly to Z axis endstop G1 H1 Z5 F6000 ; lift Z relative to current position G1 H1 Z-335 F1800 ; move Z down stopping at the endstop G90 ; absolute positioning -
RE: G28 Z error homing failedposted in Duet Web Control
@frnknstn i can home x and y. when i tell it to home z it starts probing, when thats complete i get errors
-
RE: G28 Z error homing failedposted in Duet Web Control
@gixxerfast i have been trying to figure this out on my own so i wasnt bothering people. but for some reason i think i keep making it worse.
I am kind of running a voron2.4, i am running the voron gantry style with Duet3 6hc and expansion
I installed a z stop thinking i was suppose to use that then the bed levels from that setting. but i keep reading i dont need a z endstop. So im not sure. I am really trying to learn this but i think someone telling what to do and why its that way is the only way it seems i can comprehend this stuff. -
RE: G28 Z error homing failedposted in Duet Web Control
@gixxerfast so my z home has to be off an estop. I cant use a specific point on the bed with the probe. Im not trying to be a pest i am trying to learn
-
G28 Z error homing failedposted in Duet Web Control
; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"duet3" ; Set machine name M552 S1 ; Enable network ;*** Access point is configured manually via M587 M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet M575 P1 S1 B57600 ; Panel Due ; Printer geometry M669 K1 ; Select CoreXY mode M208 X0:272 Y0:243 Z0:400 ; Axis Limits M564 H0 ; allow unhomed movement ;------- drives from top--------------------------------------------------- ; B -------+------ A ; | P.02 | P.03 | ; -------+------- Z-Drives ; | P0.1 | P0.4 | ; -------+------- ; Front ; Drive Mappings M569 P0.0 S1 V0 ; Drive 0: E Axis M569 P0.1 S0 V0 ; Drive 1: Z-LeftFront Axis M569 P0.2 S1 V0 ; Drive 2: Z-LeftRear Axis M569 P0.3 S0 V0 ; Drive 3: Z-RightRear Axis M569 P0.4 S1 V0 ; Drive 4: Z-RightFront Axis M569 P1.0 S1 V0 ; Drive 5: Expansion: B motor (X-axis) M569 P1.1 S1 V0 ; Drive 6: Expansion: A motor (Y-axis) ; Motor remapping for Quad Z and axis Limits M584 X1.0 Y1.1 Z0.1:0.2:0.3:0.4 E0.0 ; Motor mapping M671 X-76.2:-76.2:406.4:406.4 Y0:374.65:374.65:0 S20 ; Z leadscrews positions Left Front - Let Rear - Right Rear - Right Front ; Microstepping and Speed M350 X32 Y32 E16 Z16 I1 ; Configure microstepping with interpolation M92 X200.00 Y200.00 Z200.00 E400.00 ; Set steps per mm 1.8 motors ; Speeds, Acceleration and Jerk M566 X400.00 Y400.00 Z25.00 E600.00 P1 ; Set maximum instantaneous speed changes (mm/min) M203 X12000.00 Y12000.00 Z1000.00 E3600.00 ; Set maximum speeds (mm/min) M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; Set accelerations (mm/s^2) ; Motor currents M906 X1200.00 Y1200.00 Z1200.00 E700.00 I60 ; Set motor currents (mA) and motor idle factor in percent M84 S600 ; Set idle timeout ; Endstops for each Axis M574 X2 S1 P"io0.in" ; Set X endstop controlled by switch M574 Y2 S1 P"io1.in" ; Set Y endstop controlled by switch ; Z probes M558 K0 P8 C"^io2.in" T18000 F400 H5 A5 S0.01 R0.2 ;G31 X-40 Y-10 Z0 P25 I1 ; Set Probe Offset and Z height to 0 ready for calibration ;G31 X-40 Y-10 Z1.458 P25 I1 ; 0mm (1.458) ;G31 X-40 Y-10 Z1.278 P25 I1 ; Set Probe Offset and height for z = nozzle gap (0.18mm) for a layer height of 0.2mm ;G31 X-40 Y-10 Z1.338 P25 I1 ; Set Probe Offset and height for z = nozzle gap (0.12mm) for a layer height of 0.15mm ;G31 X-40 Y-10 Z1.378 P25 I1 ; Set Probe Offset and height for z = nozzle gap (0.08mm) for a layer height of 0.1mm ; Stallgaurd Sensitivy (maybe use to pause print after crash) M915 X S2 F0 H200 R0 ; Set X axis Sensitivity 1.8 motors M915 Y S2 F0 H200 R0 ; Set y axis Sensitivity 1.8 motors ; Input Shaper and Accelerometer ;M955 P0 C"io4.out+io4.in" ;M593 F46.75 S0.2 ;M593 F19 P4 S0.3 ; experimental ; Z Probe Offset (Probe behind Afterburner) G31 P500 X0 Y21 Z5-.07 ; Heaters M308 S0 P"temp_0" Y"thermistor" A"Bed" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out_0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 R0.181 C640.6 D3.19 S1.00 ; set model parameters for heater 1 and use PID mode M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"temp_1" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out_1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.436 C191.9 D3.44 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"out7" Q500 ; Parts cooling create fan 0 on pin out7 and set its frequency M106 P0 S0 H-1 M950 F1 C"out8" Q500 ; Extruder create fan 1 on pin out8 and set its frequency M106 P1 T45 H1 ; Fans Electronic compartment & Exhaust ;M950 F1 C"out3" Q100 ; Creates Case Fan 1 ;M106 P1 T40 S150 H0 ; Case Fan 1 Settings (Turns on at 60°C tool temp) at low speed ;M950 F2 C"out4" Q100 ; Creates Case Fan 2 ;M106 P2 T40 S150 H0 ; Case Fan 2 Settings (Turns on at 60°C tool temp) at low speed ;M950 F5 C"out7" Q100 ; Creates Case Fan 2 ;M106 P5 T95 S50 H0 ; Exhaust fan ; Filament Runout sensor ;M950 J4 C"io5.in" ; Input 4 filament sensor ;M581 P1 T2 S1 R1 ; Filament Sensor P1 triggers inactive-to-active edge (S1) tigger2.g (T2) only when printing (R1) ;M591 D0 P1 C"io5.in" S1 ; Filament Sensor ; Tools M563 P0 D0 H1 F0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C T0; bed.g file for RepRapFirmware, generated by Escher3D calculator M561 ; clear any existing bed transform M401 ; deploy Z probe if necessary G30 P0 X20 Y20 Z-99999 ; define 4 points in a clockwise direction around the bed, starting near (0,0) G30 P1 X20 Y240 Z-99999 G30 P2 X240 Y240 Z-99999 G30 P3 X240 Y20 Z-99999 G30 P4 X100 Y100 Z-99999 S4 ; finally probe bed centre, and calculate compensation M402 ; retract the Z probe G1 X0 Y0 F5000 ; move the head to the corner (optional)I am able to get the probing done then when its done probing i get an error.