Ok this is strange... Like I said this is a new install and I'm just configuring things. I turned on the hotend and noticed that the hotend fan did not come on. I manually turn it on using the dashboard in DWC, and the fan turns on but also the light for the knob on the display. If it turn the fan off again the knob light stays on
but the blank panel also turns on too.
Note: I found the issue why the fan was not turning on, I needed to change to H1 to put it on heater 1. Weird thing, now the panel at least lights up? Not sure what that has to do with a tool fan.
Here is my config.
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Mulcore" ; set printer name
M669 K1 ; select CoreXY mode
M918 P1 E4 F2000000 ; configure direct-connect display
; Drives
M569 P0.1 S1 ; physical drive 0.0 goes forwards
M569 P0.0 S0 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.4 S1 ; physmm/min)
M201 X1000.00 Y900.00 Z100.00 E600.00 ; set accelerations (mm/s^2)
M906 X700 Y700 Z300 E600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
ical drive 0.3 goes forwards
M584 X0.1 Y0.0 Z0.2 E0.4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z1096.00 E655.00 ; set steps per mm
M566 X900.00 Y900.00 Z100.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z2000.00 E4200.00 ; set maximum speeds (
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X200 Y200 Z200 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin io0.in
M574 Y2 S1 P"!io1.in" ; configure active-high endstop for high end on Y via pin io1.in
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; Z-Probe
M950 S0 C"io2.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io2.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y23 Z2 ; set Z probe trigger value, offset and trigger height
M557 X15:200 Y15:195 S20 ; define mesh grid
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4534 C9.565227e-8 ; configure sensor 0 as PT1000 on pin temp0
M950 H0 C"out1" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4376 ; configure sensor 1 as thermistor on pin e0temp
;M308 S1 P"temp1" Y"thermistor" T500000 B4723 C1.196220e-7 R4700 ; configure sensor 1 as PT1000 on pin temp1
M950 H1 C"out2" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency
M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off
M950 F2 C"out5" Q500 ; create fan 2 on pin out5 and set its frequency
M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off
M950 F3 C"out6" Q500 ; create fan 2 on pin out5 and set its frequency
M106 P3 S1 H-1 ; set fan 2 value. Thermostatic control is turned off
; LED
M950 F4 C"out0" ; create LED 4 on pin duex.fan7 and set its frequency - TOP LEFT
M106 P4 S1 ; set LED 4 value. Thermostatic control is turned OFF
; Tools
M563 P0 D0 H1 F0:1:2 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M501 ; Record