thanks it printing now
do you know, all slicers just sending gcode or i can get more feelings looking how it prints on screen on some of them?

ok i have installed cura now but it say "could not connect to device"

; Network
M552 S1							; network S0/1=off/on
M586 P0 S1                                              ; enable HTTP
M586 P1 S1                                              ; enable FTP
M586 P2 S1                                              ; enable Telnet

i tried to connect printer to repetier-host via wifi but cant found port info, is it some way to get it? may be i need something more, dont know yet

hi. i am new in rrf, just build my new delta with duetwifi (rrf v3.1) but when uploading stl file to print it, got feil

Error: Bad command: @A������ot?A\���sN�g�=��}?�ژ=���ot?A\���\"��
Error: Bad command: @A���1��
Error: Bad command: @Aq��sN�
Error: Bad command: �=P�}?��=���ot?A\���1��
Error: Bad command: @Aq����
Error: Bad command: �ot?AS���sN�[�=��}?th<=��
Error: Bad command: �ot?AS���1��
Error: Bad command: @Aq��Q�
Error: Bad command: �ot?A����sN���>�Ul?8�>��
Error: Bad command: �ot?AS���Q�
Error: Bad command: �ot?A��������=�=A����sN��
Error: Bad command: >ʱ}?�
Error: Bad command: @Aq����
Error: Bad command: @A*��Q�
Error: Bad command: �ot?A����sN����,�>�yk�i�X%$4A����T�f%
Error: Bad command: 8Ab�����>$4A����sN����,�>�yk���>$4A����T�f%
Error: Bad command: 8Ab����g�>
Error: Bad command: 8A����D�$?
Error: Bad command: 8A/���sN���,�>�N�c�?$4A0��D�$?
Error: Bad command: 8A/��¤Y`?$4AP[��sN���,�>�N��Y`?$4AP[��D�$?
Error: Bad command: 8A/�����n?
Error: Bad command: 8AU1��sN{,�,�>G�3��Y`?$4AP[����n?
Error: Bad command: 8AU1��GR�?$4A����sN{,�,�>G�3�GR�?$4A������n?
Error: Bad command: 8AU1��ꖗ?
Error: Bad command: 8A����sN�����V?�pJ�T�f%
Error: Bad command: 8Ab���y$}%OP
Error: Bad command: 8A����sN�����V?�pJ��g�>
Error: Bad command: 8A����y$}%OP
Error: Bad command: 8A�����ȸ>OP
Error: Bad command: 8A/���sNΩs��V?'B�D�$?
Error: Bad command: 8A/����ȸ>OP
Error: Bad command: 5?OP
Error: Bad command: 8A/���p
Error: Bad command: 5?OP
Error: Bad command: 8AU1��sNʀž�V?��1���n?
Error: Bad command: 8AU1��p
Error: Bad command: 5?OP
Error: Bad command: 8AU1�¼�?OP
Error: Bad command: 8A����sN[���V?Le�ꖗ?
Error: Bad command: 8A���¼�?OP
Error: Bad command: 8A����T�f%
Error: Bad command: 8Ab���sN���=�V?�pJ�T�f%
Error: Bad command: 8Ab����g��
Error: Bad command: 8A�����ȸ�OP
Error: Bad command: 8Ab����ȸ�OP
Error: Bad command: 5?OP
Error: Bad command: 5?OP
Error: Bad command: 5?OP
Error: Bad command: 8AZ
Error: Bad command: ���¿$4A
Error: Bad command: i��sNcl?,�>��?��¿$4A
Error: Bad command: i��\�п
Error: Bad command: 8AZ
Error: Bad command: �¦�ο
Error: Bad command: 8AKa��sN�"e?,�>�Nm��¿$4A
Error: Bad command: i�¦�ο
Error: Bad command: 8AKa��o#��$4A0���sN�"e?,�>�Nm�o#��$4A0��¦�ο
Error: Bad command: 8AKa��3!Ŀ
Error: Bad command: 8Al���sN}�T?,�>myоo#��$4A0���3!Ŀ
Error: Bad command: 8Al������$4A�@��sN}�T?,�>myо���$4A�@��3!Ŀ
Error: Bad command: 8Al���.~��
Error: Bad command: 8As%��sNP+
Error: Bad command: 8As%��GR��$4A����sNP+
Error: Bad command: 8As%��ꖗ�
Error: Bad command: 8A����sN
Error: Bad command: 8AZ
Error: Bad command: ��2�OP
Error: Bad command: 8AKa��sN
Error: Bad command: 8AKa��2�OP
Error: Bad command: 8AKa����OP
Error: Bad command: 8Al���sN)�D?�V?L�3!Ŀ
Error: Bad command: 8Al�����OP
Error: Bad command: 8Al���~4׿OP
Error: Bad command: 8As%��sN��6?�V?:��.~��
Error: Bad command: 8As%��~4׿OP
Error: Bad command: 8As%��r�¿OP
Error: Bad command: 8A����sN)� ?�V?���ꖗ�
Error: Bad command: 8A����r�¿OP
Error: Bad command: �ot?A72��sN]��>�Ul? OŽC��=�=A�D���
Error: Bad command: �ot?A72�†�=�=AV|��sN]��>�Ul? OŽ��=�=AV|���
Error: Bad command: �ot?A72��́�ot?AsQ��sN��>�Ul?�U-���=�=AV|��́�ot?AsQ���@ٿ=�=AR���sN��>�Ul?�U-��@ٿ=�=AR���́�ot?AsQ�šs�ot?A
Error: Bad command: ���sN���>�Ul?X�p��@ٿ=�=AR��šs�ot?A
Error: Bad command: ������=�=Az��sN���>�Ul?X�p����=�=Az�šs�ot?A
Error: Bad command: ����Ͽot?Af���sN�]?,�>eh�>�xʿ
Error: Bad command: 8A�������$4Aڤ��Rƻ�
Error: Bad command: 8AiP��sN�]?,�>eh�>Rƻ�
Error: Bad command: 8AiP�����$4Aڤ��SK��$4A�9��sN��H?,�>�f�>Rƻ�
Error: Bad command: 8AiP��SK��$4A�9���c��
Error: Bad command: 8A���sN��H?,�>�f�>�c��
Error: Bad command: 8A���SK��$4A�9��%G��$4A����sN9�+?,�>o#?�c��
Error: Bad command: 8A���%G��$4A�����
Error: Bad command: 8A�Z��sN9�+?,�>o#?�
Error: Bad command: K�
Error: Bad command: 8At���sN�6?,�>ZDB?'
Error: Bad command: K�
Error: Bad command: K�
Error: Bad command: 8At���ؖ>�$4A����r��
Error: Bad command: 8A5���sNx�>?�V?�W�>*޿OP
Error: Bad command: 8A���—	οOP
Error: Bad command: 8A����Rƻ�
Error: Bad command: 8AiP��sN��,?�V?�E�>�	οOP
Error: Bad command: 8AiP�³y��OP
Error: Bad command: 8AiP���c��
Error: Bad command: 8A���sN�{?�V?�1?�y��OP
Error: Bad command: 8A����{��OP
Error: Bad command: 8A����
Error: Bad command: 8A�Z��sN}�>�V?I'?�{��OP
Error: Bad command: 8A�Z�…�^�OP
Error: Bad command: 8A�Z��'
Error: Bad command: K�
Error: Bad command: 8At���sN�}�>�V?o�:?��^�OP
Error: Bad command: K�
Error: Bad command: 8At����f	�OP
Error: Bad command: K�
Error: Bad command: 8At���r��
Error: Bad command: 8A5���sN>�#>�V?�QG?�f	�OP
Error: Bad command: 8A5��º�9�OP
Error: Bad command: ?Y���=�=A�����{��OP
Error: Bad command: ?�yx�=�=AO_���{��OP
Error: Bad command: �ݵJ?�X?V1O�=�=A���º�9�OP
Error: Bad command: �ot?AS��…��=�=A���sN���>�Ul?8�>���=�=A�����
Error: in GCode file line 1172 column 161: GCode command too long
Cancelled printing file 0:/gcodes/Floor_Bedholder v6.stl, print time was 0h 0m

printer kinematics works fine from web interface, bed levelling too. What i do wrong?

feil was here:

M558 P8 R0.4 F1200 H10 T6000

must be like this:

M558 C"zprobe.in" P8 R0.4 F1200 H10 T6000

thanks to dc42, he gave a anser at another forum

hi. i have duetwifi with 3.1 firmware and just get a smart effector. when try to do z probe i get this feil:

Error: G30: Z probe 0 not found

what i do wrong?

config:

; General preferences
G90														; Absolute_cordinats
M83													; Relative_extrusion
M550 P"DeltaZ"											; Printer_"name" (http://printer_name)
M665 R105 L288.08 B80 H203.35							; R=delta_radius L=diagonal_rod B=printable_radius H=homed_height
M666 X0 Y0 Z0											; Endstop_correction
M208 S1 Z0					 							; S1=delta Z=Z_min(mm)

; Network
M552 S1													; network S0/1=off/on
M586 P0 S1                                              ; enable HTTP
M586 P1 S0                                              ; disable FTP
M586 P2 S0                                              ; disable Telnet

; Drives
M569 P0 S1												; P=driver_nr S0/1=revers/norm
M569 P1 S1												; P=driver_nr S0/1=revers/norm
M569 P2 S1												; P=driver_nr S0/1=revers/norm
M569 P3 S1												; P=driver_nr S0/1=revers/norm
M584 X0 Y1 Z2 E3										; Driver_mapping
M350 X16 Y16 Z16 E16 I1                                 ; set microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E150.00						; Steps_per_mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00				; Speed_change(mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00				; Speed_max(mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00				; Acceleration(mm/s^2)
M906 X1500 Y1500 Z1500 E1500 I0							; Peak_current(mA) I=Power_after_timeout(%)
M84 S90													; S=timeout(seconds) 

; Axis Limits
M208 Z0 S1                                              ; set minimum Z

; Endstops
M574 X2 S1 P"xstop"										; X=0/1/2=none/low/high_end S1/2/3/4=microswitch("!"inverts)/Z_probe/stall_detection_stops_all_motors/stall_detection
M574 Y2 S1 P"ystop"										; X=0/1/2=none/low/high_end S1/2/3/4=microswitch("!"inverts)/Z_probe/stall_detection_stops_all_motors/stall_detection
M574 Z2 S1 P"zstop"										; X=0/1/2=none/low/high_end S1/2/3/4=microswitch("!"inverts)/Z_probe/stall_detection_stops_all_motors/stall_detection

; Calibration
M558 P8 R0.4 F1200 H10 T6000							; Z-Probe			C=pin P=type R=Recovery_time F=probing_speed H=distance T=move_speed A=point_times S=tolerance(0.03mm) 
G31 P100 X0 Y0 Z-0.1									; Options			P=trigger XY=offsett Z=trigger
M557 R80 S15											; Grid_Options		R=radius S=Space

; Bed
M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8	; Define_sensor		S=nr P=pin Y=type (TBC=Semitec_104GT-2) R=resistor
M950 H0 C"bedheat" Q10 T0								; Define_heater		H=nr C=pin Q=Hz T=temp_sensor_nr
M143 H0 S130											; Temp_limit		H=heater_nr S=max_temp
M307 H0 A858.4 C741.7 D4.2 V24.2 B0 S1.0				; Heater_options	H=heater_nr A=model_gain C=model_time_constant D=dead_time V=volts B0/1=PID/bang_bang S=max_PWM(1.0_max)
M140 H0                                                 ; map heated bed to heater 0

; HotEnd
M308 S1 P"spi.cs1" Y"rtd-max31865"						; Define_sensor		S=nr P=pin Y=type R=resistor F=Hz(50/60) W=wire(if_3)
M950 H1 C"e0heat" T1									; Define_heater		H=nr C=pin Q=Hz T=temp_sensor_nr
M143 H1 S300											; Temp_limit		H=heater_nr S=max_temp
M307 H1 A1029.2 C403.6 D6.7 V24.1 B0 S1.00				; Heater_options	H=heater_nr A=model_gain C=model_time_constant D=dead_time V=volts B0/1=PID/bang_bang S=max_PWM(1.0_max)

; Fans
M950 F0 C"fan0"											; Define_fan		F=nr C=pin Q=Hz
M106 P0 L0.5 X1.0 B5 H1 T50:100							; Fan_options		P=nr S=speed(1.0_max) L=min_speed X=max_speed B=max_speed_seconds_onstart H=temp_sensor_nr T=temp_on
; M950 F1 C"fan1" Q500										; Define_fan		F=nr C=pin Q=Hz
; M106 P1 S1 H-1											; Fan_options		P=nr S=speed(1.0_max) L=min_speed X=max_speed B=max_speed_seconds_onstart H=temp_sensor_nr T=temp_on

; Tools
M563 P0 S"e3d" D0 H1 F0									; Define_tool		P=nr S="name" D=extruder H=heater(s) F=fan(s) 
G10 P0 Z0 R0 S0											; Tool_options		P=tool_nr XYZ=offset(mm) R=off_temp S=on_temp
; M563 P1 S"Volcano" D0 H1 F0:1								; Define_tool		P=nr S="name" D=extruder H=heater(s) F=fan(s) 
; G10 P1 X0 Y0 Z0											; Tool_options		P=tool_nr XYZ=offset(mm) R=off_temp S=on_temp

; Custom settings are not defined

; Miscellaneous
M501                                                    ; load saved parameters from non-volatile memory
T0                                                      ; select first tool

when i try to change sensitivity i get this feil

Error: M672: Invalid Z probe index

When i touching it, led works )