Posts made by akinori

@dc42 You had right! Mi wires was connected in proper order but, for some reason it doesn't work. But I use different wires, crimped again and everything works

@phaedrux Through this website http://filament23d.dk
It was closest avaible option. I bought it 12/02/2022 and arrived to me in Poland around two weeks later.
I wrote to hobby-store.pl about the chance to buy this part but they did not respond to me

@phaedrux
Yeah, I go step by step with this guide. I disassemble effector but, probe-z value is still on 1000 :c

5.04.2022, 18:17:43 M98 P"config.g"

HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: in file macro line 77 column 13: M591: expected string expression
Warning: Macro file config-override.g not found

5.04.2022, 18:17:28 M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.0 (2022-03-15 18:58:31) running on Duet Ethernet 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JTD6-3SS6N-19DLQ
Used output buffers: 6 of 24 (12 max)
=== RTOS ===
Static ram: 23868
Dynamic ram: 69092 of which 268 recycled
Never used RAM 18852, free system stack 192 words
Tasks: NETWORK(ready,21.0%,240) HEAT(notifyWait,0.0%,338) Move(notifyWait,0.0%,364) MAIN(running,75.6%,448) IDLE(ready,3.4%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:25 ago, cause: power up
Last software reset at 2022-04-04 19:10, reason: User, GCodes spinning, available RAM 16112, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 26.0, current 29.2, max 29.6
Supply voltage: min 24.0, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2022-04-05 18:17:25
Cache data hit count 938378659
Slowest loop: 5.74ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 8.50ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

@dc42 LED is blink 2 times when power on, but it doesn't react when I tap nozzle.

Hello, I have Duet 2 Ethernet (rev. 1.3, soft ver. 3.4) and Smart Effector (rev. 3.0). I tried almost everything to went through auto callibration but always my z-probe value's 1000 and callibration process's end immediately. I'm sure cable wiring is corectly done. Crimps are deep in connectors. I tried tips from similar topic but it doesn't help: https://forum.duet3d.com/topic/2739/z-probe-stuck-at-1000-with-smart-affector (shorting pin of z-probe on duet board give 0 value like it should). I'm fighting with duet 2 and smart effector nearly a month and I'm losing hope it will finally work

My config.g file:
; Configuration file for Duet Ethernet (firmware version 3.4)
; executed by the firmware on start-up
; generated by RepRapFirmware Configuration Tool v3.3.10 on Tue Mar 22 2022 21:42:46 GMT+0100 (czas środkowoeuropejski standardowy)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

; Delta Settings
M665 L440.380 R226.821 H407 B185.0 X0 y0 z0 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 y0 z0 A0.00 B0.00 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"Anycubic Predator" ; Set machine name
M551 P"" ; Set password
M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E415 ; Set steps per mm
M566 X3000 Y3000 Z3000 E3000 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z12000.00 E12000 ; Set maximum speeds (mm/min)
M201 X9000.00 Y9000.00 Z9000.00 E6000.00 ; Set accelerations (mm/s^2)
M906 X1400.00 Y1400.00 Z1400.00 E1000.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Retraction
M207 S2.5 F7000 R0.1 T2500 Z0.5 ; Firmware retraction

; Axis Limits
M208 Z0 S1 ; Set minimum Z

; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M558 P5 R0.4 H3 F1200 T6000 C"zprobe.in+zprobe.mod" ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.1 ; set Z probe trigger value, offset and trigger height
M557 R180 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured
M591 D0 P2 C4 S1 ; Activate filament sensor
M404 N1.75 ; Set for print monitor
M575 P1 B57600 S1 ; Paneldue baud rate

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory