Yes I did that and I will add it again in config description below but motor still sounds rough and vibrates:
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Apr 28 2020 19:28:52 GMT-0400 (Eastern Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BILLy 2 Extruders Config File" ; set printer name
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M569 P10 S0 T2.5:2.5:5:0 ; physical drive 10 goes backwards
M584 X0 Y1 Z2 E3:10 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X320.00 Y320.00 Z320.00 E320.00:320.00 ; set steps per mm
M566 X900.00 Y900.00 Z900.00 E200.00:200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X3000.00 Y3000.00 Z3000.00 E1000.00:1000.00 ; set maximum speeds (mm/min)
M201 X25.00 Y25.00 Z25.00 E10.00:10.00 ; set accelerations (mm/s^2)
M906 X2000 Y2000 Z2000 E2000:2000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X930 Y155 Z345 S0 ; set axis maxima
; Endstops
M574 X1 Y1 Z1 S1 ; set active high endstops
; Z-Probe
; Heaters
M140 H-1 ; disable heated bed
; Fans
; Tools
M563 P0 S"Print Head" D0:1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M567 P0 E0.50:0.50 ; set mixing ratios for tool 0
M563 P1 S"Conc Stuffer" D0:1 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
M567 P1 E0.50:0.50 ; set mixing ratios for tool 1
; Custom settings
Mixing of Extruders RRF Config File Edited 4-28-20
; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool
T10 ; select first tool
20200513_114704[1].jpg