• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login
  1. Home
  2. Arnold
  3. Posts
  • Profile
  • Following 0
  • Followers 0
  • Topics 3
  • Posts 10
  • Best 0
  • Controversial 0
  • Groups 0

Posts made by Arnold

  • RE: Noz heater wiring shorted, spark, probs

    @Arnold although all board front and rear traces and components appear fine

    posted in General Discussion
    undefined
    Arnold
    24 Dec 2022, 16:28
  • RE: Noz heater wiring shorted, spark, probs

    @dc42 Not that i feel. problem now is 24v at vin terminals nut 1.7v at DWC sensor. i fear i may have popped it...

    posted in General Discussion
    undefined
    Arnold
    24 Dec 2022, 16:26
  • RE: Noz heater wiring shorted, spark, probs

    My 5v is gone, plugged in usb and we're back though not ideal

    posted in General Discussion
    undefined
    Arnold
    24 Dec 2022, 15:02
  • Noz heater wiring shorted, spark, probs

    Panels dead, always on fan off. Fuses ok, no signs of burnt out board components.
    Any ideas helpful! It's a WiFi ,
    Rob

    posted in General Discussion
    undefined
    Arnold
    24 Dec 2022, 12:10
  • Broken antenna connection to esp module

    just can't get antenna to seat properly, it must have been pulled roughly. Can I use a workaround for my duet wifi?

    posted in Duet Hardware and wiring
    undefined
    Arnold
    8 Aug 2022, 11:39
  • RE: Just cannot resolve motor phase errors and shifting

    @Arnold said in Just cannot resolve motor phase errors and shifting:

    After no previous probs I just can't stop the above. Ive continuity on the motor phases, not going too fast, currents are ok. Wiring tests fine. Its always x, shifted to E0 driver, same reports. Can be either phase A or B. Multiple reports repeatedly. Haven't tried a diff motor. Ive had a brain injury so Im not as sharp as I was but this is essentially making my machine useless. Its usually within first few layers. I prefer simplify 3d. I have noticed my Vin can wobble between 10.5 to 12.5 or so. All the posts here haven't helped yet. Any ideas clever ones? Thank you

    posted in General Discussion
    undefined
    Arnold
    7 Jan 2021, 14:37
  • RE: Just cannot resolve motor phase errors and shifting

    I was sidetracked and thank everyone for their responses. In the end I dropped the z motor current 200ma and so far so good. Thought id tried it before but hey.

    Rob

    posted in General Discussion
    undefined
    Arnold
    7 Jan 2021, 14:35
  • RE: Just cannot resolve motor phase errors and shifting

    Thanks all I'll get back to you shortly. Rob

    posted in General Discussion
    undefined
    Arnold
    20 Dec 2020, 20:00
  • RE: Just cannot resolve motor phase errors and shifting

    @Arnold Its just shifted x about 30mm as I write....

    posted in General Discussion
    undefined
    Arnold
    20 Dec 2020, 16:37
  • Just cannot resolve motor phase errors and shifting

    After no previous probs I just can't stop the above. Ive continuity on the motor phases, not going too fast, currents are ok. Wiring tests fine. Its always x, shifted to E0 driver, same reports. Can be either phase A or B. Multiple reports repeatedly. Haven't tried a diff motor. Ive had a brain injury so Im not as sharp as I was but this is essentially making my machine useless. Its usually within first few layers. I prefer simplify 3d. I have noticed my Vin can wobble between 10.5 to 12.5 or so. All the posts here haven't helped yet. Any ideas clever ones? Thank you

    posted in General Discussion
    undefined
    Arnold
    20 Dec 2020, 16:36
Unless otherwise noted, all forum content is licensed under CC-BY-SA