(

this one.

haha! finally i'm the first to achieve something

I just ordered some of the fuses. don't want to run the board unprotected

yep. just measured again in high ohm range, 15M.

thanks for your help, this saves me a ton of money

What type of fuse is this?
I'm confident, that i can replace it

Overload... i guess it broke -.-

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.0 or 1.01 FIRMWARE_DATE: 2019-06-13b2

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.4 on Sat Oct 12 2019 17:04:55 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                         ; send absolute coordinates...
M83                                         ; ...but relative extruder moves
M550 P"Predator"                            ; set printer name
M665 R220 L440.4 B185 H420.607                  ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                               ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                     ; enable network
M586 P0 S1                                  ; enable HTTP
M586 P1 S0                                  ; disable FTP
M586 P2 S0                                  ; disable Telnet
M575 P1 B57600 S1				;Serial Port for Panel Due

; Drives
M569 P0 S0                                  ; physical drive 0 goes forwards
M569 P1 S0                                  ; physical drive 1 goes forwards
M569 P2 S0                                  ; physical drive 2 goes forwards
M569 P3 S1                                  ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                            ; set drive mapping
M350 X16 Y16 Z16 I1
M350 E16 I1                     ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E412;  E399	    ; set steps per mm
M566 X600.00 Y600.00 Z600.00 E160.00  ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E10000.00 ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E1000.00    ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I50             ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 Z0 S1                                  ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                            ; set active low and disabled endstops

; Z-Probe
M558 P5 R0.4 H20 F1200 T6000 A10 S0.02                 ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.13                           ; set Z probe trigger value, offset and trigger height
M557 R180 S18                               ; define mesh grid


; Heaters
M305 P0 T100000 B4138 C0 R4700                 ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                ; set temperature limit for heater 0 to 120C
M305 P1 B4725 C7.060000e-8 R4700                ; set thermistor + ADC parameters for heater 1
M143 H1 S280   
;M305 P2 B4725 C7.060000e-8 R4700                ; set thermistor + ADC parameters for heater 1
;M143 H2 S280                                ; set temperature limit for heater 1 to 280C

; Fans


M106 P0 S0 F100  C"Bauteillüfter"                    ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0.66 H1 F100 T60 L0.3 X0.75              ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                            ; define tool 0
G10 P0 X0 Y0 Z0                             ; set tool 0 axis offsets
G10 P0 R0 S0                                ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M98 P0:/sys/retract.g
T0
M501
M572 D0 S0
G29 S1

I'm measuring 120k for the hotend Thermistor and 114k for the Bed thermistor, which should be fine....

I mesaure a Voltage of 3.2V from Thermistor0-pin, Thermistor1-pin and Thermistor2-pin to GND. ---However, the VSSA voltage is slowly crawling from 3.2V to 0V while i measure between VSSA and GND. shouldnt VSSA be GND potential?

edit: i just noticed... there is a resettable fuse F1... how do i reset it?

I have a Delta with two Smart effectors. After changing my effector BOTH, bed and hotend started reading 2000°C. I did not change any wireing or configuration. If it only was the hotend, it culd be a broken wire, but the fact that tne bed ALSO reads 2000°C makes me suspicious... I also tried connecting the hotend thermistor to the second channel, same here.

Did my duet just break?

Hi,
is it possible to connect a Reprap-Smart-Controller/ Full-Graphic-Controller?