Posts made by bam

@Veti

Either right click and delete, or if that won't work, you can try and do it from the SBC side.

i did it from the duet3webcontrol.

sorry if i dont know anything about these and i jumped in feet first.

thanks for all the helps @dc42 @Veti @Phaedrux @bearer i promise you i will be back. have to make a hardware store run to find an (actual) twisted pair, not this spliced mess, and then start wiring motors and sensors.

@Phaedrux yeah theres nothing here so idk

@Veti i dont know why the file is in there, not sure how to delete either. mightve shown up with the .bin i downloaded.

this whole time ive just been trying to get the boards online and the software updated. I can config the printer later.

twisted pair wasnt actually twisted. just looked twisted.

@Veti I Got It!!! Finally!!

m122 b1
Diagnostics for board 1:
Duet EXP3HC firmware version 3.2-RC2 (2020-12-24)
Bootloader ID: not available
Never used RAM 154536, free system stack 200 words
HEAT 75 CanAsync 94 CanRecv 87 TMC 64 MAIN 173 AIN 257
Last reset 00:00:35 ago, cause: software
Last software reset data not available
Driver 0: position 0, 100.0 steps/mm, standstill, reads 63861, writes 16 timeouts 0, SG min/max 0/0
Driver 1: position 0, 100.0 steps/mm, standstill, reads 63863, writes 16 timeouts 0, SG min/max 0/0
Driver 2: position 0, 80.0 steps/mm, standstill, reads 63871, writes 11 timeouts 0, SG min/max 0/0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.1V, V12: 12.2V
MCU temperature: min 45.9C, current 46.1C, max 46.1C
Ticks since heat task active 73, ADC conversions started 35564, completed 35564, timed out 0
Last sensors broadcast 0x00000006 found 2 76 ticks ago, loop time 0
CAN messages queued 243, send timeouts 0, received 252, lost 0, free buffers 36
1/2/2021, 1:13:10 AM m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-RC2 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TJ-6JTD2-3SN6K-9BAQU
Used output buffers: 1 of 40 (13 max)
=== RTOS ===
Static ram: 149788
Dynamic ram: 62676 of which 136 recycled
Never used RAM 146232, free system stack 200 words
Tasks: Linux(ready,119) HEAT(blocked,188) CanReceiv(blocked,836) CanSender(blocked,371) CanClock(blocked,360) TMC(blocked,53) MAIN(running,1217) IDLE(ready,19)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:15 ago, cause: software
Last software reset time unknown, reason: StuckInSpinLoop, GCodes spinning, available RAM 147880, slot 1
Software reset code 0x0083 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0040080f BFAR 0x00000000 SP 0x204334e4 Task Linu Freestk 443 ok
Stack: 00429a2d 00429ab0 61000000 a5a5a5a5 a5a5a5a5 a5a5a5a5 00000000 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU temperature: min 43.8, current 46.0, max 46.1
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Driver 0: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 23491, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 23488, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 23488, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-01-02 01:13:08
Slowest loop: 0.45ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 55, send timeouts 0, received 95, lost 0, longest wait 1ms for reply type 6018, free buffers 48
=== SBC interface ===
State: 4, failed transfers: 0
Last transfer: 2ms ago
RX/TX seq numbers: 442/442
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x2c8a8
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.2.0-rc2
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 35.67
Maximum length of RX/TX data transfers: 5196/900

@dc42 and now this

Warning: Incompatible firmware, please upgrade as soon as possible

@dc42 what does this mean?

M32 "0:/gcodes/Duet3Firmware_EXP3HC.bin"
Error: Unterminated string in line 3

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TJ-6JTD2-3SN6K-9BAQU
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162320 of which 100 recycled
Exception stack ram used: 272
Never used ram: 75920
Tasks: NETWORK(ready,1968) HEAT(blocked,476) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,192) MAIN(running,5056) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:06:53 ago, cause: software
Last software reset details not available
Error status: 0
MCU temperature: min 43.7, current 44.6, max 44.8
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Driver 0: standstill, reads 6854, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 6855, writes 14 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 6855, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 6858, writes 11 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 6856, writes 14 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 6856, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-01-01 23:45:44
Slowest loop: 2102.42ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.81ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8

• Ethernet -
  State: disabled
  Error counts: 0 0 0 0 0
  Socket states: 0 0 0 0 0 0 0 0
  === CAN ===
  Messages sent 1636, longest wait 0ms for type 0
  === Linux interface ===
  State: 0, failed transfers: 7
  Last transfer: 17ms ago
  RX/TX seq numbers: 46099/13071
  SPI underruns 7, overruns 7
  Number of disconnects: 0
  Buffer RX/TX: 0/0-0
  === Duet Control Server ===
  Duet Control Server v3.1.1
  Code buffer space: 4096
  Configured SPI speed: 8000000 Hz
  Full transfers per second: 1.17
  1/1/2021, 11:45:04 PM m115
  FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2020-05-19b2

@dc42 i just took a look and the wires are not crossed

@bam fast flash is no connection to mb

@dc42 changed the can address switches on 3hc to 1, same as the config.g file. now we have a slow flash on the mb and a fast flash on the eb

@Veti ; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.0 on Fri Jan 01 2021 12:00:51 GMT-0500 (Eastern Standard Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 3" ; set printer name

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M569 P0.5 S1 ; physical drive 0.5 goes forwards
M569 P1.0 S1 ; physical drive 1.0 goes forwards
M569 P1.1 S1 ; physical drive 1.1 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.4:0.5:1.0:1.1 ; set drive mapping
M350 X16 Y16 Z16 E16:16:16:16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E100.00:100.00:100.00:100.00 ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00:300.00:300.00:300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00:6000.00:6000.00:6000.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E10000.00:10000.00:10000.00:10000.00 ; set accelerations (mm/s^2)
M906 X500 Y500 Z500 E800:800:800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X-50 Y-10 Z0 S1 ; set axis minima
M208 X300 Y300 Z350 S0 ; set axis maxima

; Endstops
M574 Z1 S3 ; configure sensorless endstop for low end on Z

; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X20:200 Y20:200 S40 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M308 S1 P"1.temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin 1.temp0
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; set temperature limit for heater 1 to 300C
M308 S2 P"1.temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin 1.temp1
M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S300 ; set temperature limit for heater 2 to 300C

; Fans
M950 F0 C"1.out3" Q500 ; create fan 0 on pin 1.out3 and set its frequency
M106 P0 S1 H1:2 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"1.out4" Q500 ; create fan 1 on pin 1.out4 and set its frequency
M106 P1 S1 H1:2 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
T0 ; select first tool

@dc42 That’s probably the issue then because I am just using standard issue phone cord

@dc42 4 flashes then it stops then 4 flashes. It’s asking for firmware update. I think.

@dc42 4 flashes only on the 3hc

@dc42 when I had the main board on 3.2 it wouldn’t talk to the DWC

@Veti that happened when I flipped the switch off

m409
{"key":"","flags":"","result":{"boards":[{}],"directories":{},"fans":[],"heat":{},"inputs":[{},{},{},{},{},{},{},{},{},{},{},{}],"job":{},"limits":{},"move":{},"network":{},"sensors":{},"seqs":{},"spindles":[{},{}],"state":{},"tools":[],"volumes":[{}]}}
12/31/2020, 11:18:40 PM Warning: 12V under-voltage event (9.4V)
12/31/2020, 11:16:15 PM m98 p"config.g"
12/31/2020, 11:16:03 PM m98 p "config.g"
Error: M98: non-empty string expected
12/31/2020, 11:15:53 PM m98 p config.g
Error: M98: non-empty string expected
12/31/2020, 11:15:42 PM m98 p
Error: M98: non-empty string expected
12/31/2020, 11:15:37 PM m98
Error: M98: missing parameter 'P'
12/31/2020, 11:14:50 PM Download of config.g successful after 0s
12/31/2020, 11:14:08 PM M98 P"config.g"
12/31/2020, 11:13:59 PM M98 P"config.g
Error: Unterminated string
12/31/2020, 11:13:35 PM M98 P"config.g
Error: Unterminated string
12/31/2020, 11:12:22 PM m115 b15
Error: M115: Response timeout: CAN addr 15, req type 6024, RID=2
12/31/2020, 11:12:22 PM Connection to Duet established
12/31/2020, 11:12:22 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 11:12:05 PM m115 b126
Error: M115: Response timeout: CAN addr 126, req type 6024, RID=1
12/31/2020, 11:12:05 PM Connection to Duet established
12/31/2020, 11:12:04 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 11:05:22 PM m115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2020-05-19b2
12/31/2020, 11:04:35 PM m451
12/31/2020, 11:02:56 PM M952 b126 a1
Error: M952: Response timeout: CAN addr 126, req type 2010, RID=0
12/31/2020, 11:02:56 PM Connection to Duet established
12/31/2020, 11:02:56 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 11:01:45 PM M954 b126
Warning: M954: Command is not supported
12/31/2020, 10:59:27 PM Connection to Duet established
12/31/2020, 10:59:27 PM Warning: Lost connection to Duet (Board is not available (no header))
12/31/2020, 10:57:43 PM M115 b126
Error: M115: Response timeout: CAN addr 126, req type 6024, RID=2
12/31/2020, 10:57:43 PM Connection to Duet established
12/31/2020, 10:57:43 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:54:47 PM M115 b126
Error: M115: Response timeout: CAN addr 126, req type 6024, RID=1
12/31/2020, 10:54:46 PM Connection to Duet established
12/31/2020, 10:54:46 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:53:57 PM Warning: 12V under-voltage event (9.5V)
12/31/2020, 10:52:10 PM M115 b126
Error: M115: Response timeout: CAN addr 126, req type 6024, RID=0
12/31/2020, 10:52:10 PM Connection to Duet established
12/31/2020, 10:52:10 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:50:06 PM M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2020-05-19b2
12/31/2020, 10:49:46 PM Upload of Duet3Firmware_MB6HC.bin successful after 0s
12/31/2020, 10:44:33 PM M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2020-05-19b2
12/31/2020, 10:42:49 PM M115 B1
Error: M115: Response timeout: CAN addr 1, req type 6024, RID=5
12/31/2020, 10:42:49 PM Connection to Duet established
12/31/2020, 10:42:48 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:42:44 PM M115 B123
Error: M115: Response timeout: CAN addr 123, req type 6024, RID=4
12/31/2020, 10:42:43 PM Connection to Duet established
12/31/2020, 10:42:43 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:42:33 PM M115 B121
Error: M115: Response timeout: CAN addr 121, req type 6024, RID=3
12/31/2020, 10:42:33 PM Connection to Duet established
12/31/2020, 10:42:32 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:42:21 PM M115 B122
Error: M115: Response timeout: CAN addr 122, req type 6024, RID=2
12/31/2020, 10:42:20 PM Connection to Duet established
12/31/2020, 10:42:20 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:40:47 PM m954
Warning: M954: Command is not supported
12/31/2020, 10:40:24 PM m997 b1
Error: M997: Response timeout: CAN addr 1, req type 6024, RID=1
12/31/2020, 10:40:24 PM Connection to Duet established
12/31/2020, 10:40:24 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:40:08 PM m954 b1
Warning: M954: Command is not supported
12/31/2020, 10:31:45 PM m954 b1
Warning: M954: Command is not supported
12/31/2020, 10:31:38 PM m954
Warning: M954: Command is not supported
12/31/2020, 10:26:56 PM m997 b1
Error: M997: Response timeout: CAN addr 1, req type 6024, RID=0
12/31/2020, 10:26:56 PM Connection to Duet established
12/31/2020, 10:26:55 PM Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
12/31/2020, 10:19:10 PM m575 p1b57600 s1
12/31/2020, 10:18:08 PM M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TJ-6JTD2-3SN6K-9BAQU
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 161360 of which 20 recycled
Exception stack ram used: 224
Never used ram: 77008
Tasks: NETWORK(ready,1980) HEAT(blocked,1416) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1460) TMC(blocked,204) MAIN(running,5128) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:00:40 ago, cause: software
Last software reset details not available
Error status: 0
MCU temperature: min 46.8, current 47.1, max 47.3
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.3, max 12.3, under voltage events: 0
Driver 0: standstill, reads 1305, writes 11 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 1306, writes 11 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 1306, writes 11 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 1307, writes 11 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 1307, writes 11 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 1308, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-12-31 22:18:06
Slowest loop: 3.44ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.08ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8

• Ethernet -
  State: disabled
  Error counts: 0 0 0 0 0
  Socket states: 0 0 0 0 0 0 0 0
  === CAN ===
  Messages sent 0, longest wait 0ms for type 0
  === Linux interface ===
  State: 0, failed transfers: 0
  Last transfer: 17ms ago
  RX/TX seq numbers: 60298/1291
  SPI underruns 0, overruns 0
  Number of disconnects: 0
  Buffer RX/TX: 0/0-0
  === Duet Control Server ===
  Duet Control Server v3.1.1
  Daemon:
  Finishing macro daemon.g, started by system

Next stack level
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 32.20
12/31/2020, 10:17:29 PM m997 b#
12/31/2020, 10:16:35 PM m997
12/31/2020, 9:54:11 PM Connected to duet3