I've been communicating with @gloomyandy @PCR and @jay_s_uk on the discord server since I'm using an SKR 1.4 Turbo

They have been patiently working with me until I finally got it working tonight. It was either a hardware problem (incorrect connection of jumper cables from the Pi to the board) or the wrong firmware.bin problem.

These guys are not only top notch for having ported the Duet firmware over to the LPC boards, but they really have donated a significant amount of their time to supporting the end users, being patient with those of us who are a lot less knowledgeable than them.

It's possible that this has been asked before, but I haven't had any luck searching for it.

I'm coming from Octoprint, so I need to get used to the web interface. I am very happy with the way the macros are used, and the ability to edit config files via the web interface. Integrating a camera via a livestream from an external device (such as a raspberry Pi), though not quite as easy as Octoprint, is perfectly fine by me, and makes sense.

What I can't figure out, is if there's a way to view the web cam from the same screen as the 'jog' buttons. My printer is out in my cold garage, and I only drag my laptop out there when I'm doing serious adjustments/troubleshooting. I prefer to be able to move the printer around, check what's happening via the webcam from my desk. It always made sense to me that Octoprint put the webcam on the same page as the jog buttons for this reason.

I like how configurable DWC is, and I'm hoping theres a way for me to rearrange the screens/tools/views or even create my own layout to provide access to the things that I want all on one page.

I've been communicating with @gloomyandy @PCR and @jay_s_uk on the discord server since I'm using an SKR 1.4 Turbo

They have been patiently working with me until I finally got it working tonight. It was either a hardware problem (incorrect connection of jumper cables from the Pi to the board) or the wrong firmware.bin problem.

These guys are not only top notch for having ported the Duet firmware over to the LPC boards, but they really have donated a significant amount of their time to supporting the end users, being patient with those of us who are a lot less knowledgeable than them.

@Phaedrux sure, I'll give that a try.

I'm also going to try installing Raspberry Pi OS and then adding everything from there - someone suggested that on the discord server:

https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Raspbian_Setup_Guide

The SBC is a Raspberry Pi 3 Model B Rev 1.2

I am trying to set up an SBC for my board. I downloaded (from the Duet3d webpage: https://duet3d.dozuki.com/Wiki/SBC_Setup_for_Duet_3) and installed DuetPi Lite. I got the pi up and running (WPA_SUPPLICANT and .ssh). If I try to start Duet Control Server, I get this error:

pi@duet3:~ $ sudo systemctl start duetcontrolserver
Job for duetcontrolserver.service failed because the service did not take the steps required by its unit configuration.
See "systemctl status duetcontrolserver.service" and "journalctl -xe" for details.

When I attempt to update/upgrade I get errors (see screen shot).

This is my second attempt. I downloaded a brand new image and wiped my sd card, it didn't make a difference.

It's possible that this has been asked before, but I haven't had any luck searching for it.

I'm coming from Octoprint, so I need to get used to the web interface. I am very happy with the way the macros are used, and the ability to edit config files via the web interface. Integrating a camera via a livestream from an external device (such as a raspberry Pi), though not quite as easy as Octoprint, is perfectly fine by me, and makes sense.

What I can't figure out, is if there's a way to view the web cam from the same screen as the 'jog' buttons. My printer is out in my cold garage, and I only drag my laptop out there when I'm doing serious adjustments/troubleshooting. I prefer to be able to move the printer around, check what's happening via the webcam from my desk. It always made sense to me that Octoprint put the webcam on the same page as the jog buttons for this reason.

I like how configurable DWC is, and I'm hoping theres a way for me to rearrange the screens/tools/views or even create my own layout to provide access to the things that I want all on one page.