@Phaedrux
Thanks. Looks like prusaslicer has a bunch of Z movements that are not at .2 intervals, which might be messing up the estimates
Posts made by bezz
-
RE: Prints stuck at layer 2 with Prusa Slicer
-
Prints stuck at layer 2 with Prusa Slicer
I'm having some issues with progress estimates and the displayed current layer does not go past 2. Prints fine.
Running RepRapFirmware 3.1.1 but the issue was also present with 2.05 before upgradingUpdate: The total layer count on this specific print is supposed to be 50. The layers started incrementing after layer ~150, so it seems like it is inserting 150 layers to the estimate and not incrementing until the end.
Sample snip of a layer change (neither format seems to increment the layer)
G1 X100.134 Y54.598 E0.01299 G1 X100.134 Y59.163 E0.15299 M204 S1000 G92 E0.0 G1 Z0.800 F10800.000 ;LAYER:3 ;Layer 3 G1 E-0.80000 F2100.00000 G1 X100.398 Y50.048 F10800.000 G1 E0.80000 F2100.00000 G1 F3000.000 G1 X129.157 Y50.008 E0.37187 G1 X129.757 Y50.082 E0.00781 G1 X132.696 Y50.897 E0.03944
-
RE: BLTouch Failed to enable endstops error on home
Figured it out. Had to make some changes to homez.g
G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G90 ; absolute positioning G1 X0 Y60 F6000 ; go to first probe point G30 ; home Z by probing the bed
-
BLTouch Failed to enable endstops error on home
I recently upgraded the duet firmware from 2.05 to 3.0 then 3.1.1 and I'm now unable to home Z.
When I run G28 Z I get: Error: Failed to enable endstops
Also, it used to move to a probe-able location before deploying the probe. Now it just errors.
I'm using a bltouch probe and my wiring matches
https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/KUDxTZSs3rnd3JVH.fullI'm able to deploy/retract the probe using
M280 P0 S10 ; deploy BLTouch
M280 P0 S90 ; retract BLTouchHere's my config:
{"board":"duetwifi10","expansion_boards":[],"firmware":3,"standalone":true,"nvram":false,"auto_save":{"enabled":false,"save_threshold":10,"resume_threshold":11,"gcodes_to_run":"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"},"display":{"type":0,"encoder_steps":4,"spi_frequency":2000000,"menus":[{"name":"main","value":""}],"images":[]},"geometry":{"type":"cartesian","mins":[0,0,0],"maxes":[230,215,200],"delta_radius":105.6,"homed_height":250,"low_dive_height":false,"max_carriage_travel":260,"print_radius":85,"rod_length":215,"z_min":0},"drives":[{"direction":0,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":160,"instant_dv":15,"max_speed":150,"acceleration":500,"current":1000,"driver":0,"driver_v3":"0.0","endstop_pin":"xstop","endstop_type":1,"endstop_location":2},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":160,"instant_dv":15,"max_speed":150,"acceleration":500,"current":1000,"driver":1,"driver_v3":"0.1","endstop_pin":"ystop","endstop_type":1,"endstop_location":1},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":400,"instant_dv":0.6,"max_speed":10,"acceleration":20,"current":1000,"driver":2,"driver_v3":"0.2","endstop_pin":null,"endstop":null,"endstop_type":0,"endstop_location":1},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":840,"instant_dv":6,"max_speed":20,"acceleration":250,"current":1000,"driver":3,"driver_v3":"0.3"}],"idle":{"used":true,"factor":30,"timeout":30},"homing_speed_fast":30,"homing_speed_slow":6,"travel_speed":100,"z_dive_height":5,"slow_homing":false,"probe":{"type":"bltouch","recovery_time":0.4,"trigger_height":2.5,"trigger_value":500,"x_offset":0,"y_offset":-40,"speed":2,"deploy":true,"points":[],"pwm_channel":3,"pwm_inverted":true,"pwm_pin":"exp.heater3","input_pin":"zprobe.in","modulation_pin":"zprobe.mod"},"bed_is_nozzle":false,"bed":{"present":true,"use_pid":false,"heater":0},"chamber":{"present":false,"use_pid":false,"heater":2},"heaters":[{"temp_limit":120,"scale_factor":100,"series":4700,"thermistor":100000,"beta":4138,"c":0,"channel":0,"sensor":0,"output_pin":"bedheat","sensor_type":"thermistor","sensor_pin":"bedtemp"},{"temp_limit":280,"scale_factor":100,"series":4700,"thermistor":100000,"beta":4138,"c":0,"channel":1,"sensor":1,"output_pin":"e0heat","sensor_type":"thermistor","sensor_pin":"e0temp"}],"num_nozzles":1,"toolchange_wait_for_temperatures":true,"generate_t_code":false,"tools":[{"mix_ratio":[],"number":0,"name":"","extruders":[0],"heaters":[1],"fans":[0],"x_offset":0,"y_offset":0,"z_offset":0}],"compensation_x_offset":15,"compensation_y_offset":15,"peripheral_points":3,"halfway_points":3,"calibration_factors":6,"probe_radius":85,"mesh":{"x_min":15,"x_max":230,"y_min":20,"y_max":175,"radius":85,"spacing":25},"home_first":false,"orthogonal":{"compensation":false,"height":50,"deviations":[0,0,0]},"network":{"enabled":true,"mac_address":"","name":"BezzBot","password":"","ssid":"","ssid_password":"","dhcp":true,"ip":"192.168.1.20","netmask":"255.255.255.0","gateway":"192.168.1.254","protocols":{"http":true,"ftp":false,"telnet":false}},"fans":[{"name":"","value":0,"inverted":false,"frequency":500,"thermostatic":false,"heaters":[],"trigger_temperature":45,"output_pin":"fan0"},{"name":"","value":100,"inverted":false,"frequency":500,"thermostatic":true,"heaters":[1],"trigger_temperature":45,"output_pin":"fan1"}],"custom_settings":""}
Thanks for your help