Posts made by bwenig

@Phaedrux No, they throw the same phase errors

@Phaedrux Should I try a much smaller E value? Not sure what else I could try to get these drivers to cooperate

@Phaedrux My extruder has very fine movement, so I think 160000 steps might not be too bad? Here's a video of me moving it manually:

So plugging the extruder motor into the x axis results in the same error, but I heard some clicking out of the motor, it tried to move a little bit.

I plugged the x driver back into the x motor and luckily everything still works fine.

@Phaedrux
Yes, it follows the motor and driver.
Yes I used the same wiring, and tried switching the A and B as well/
So now I have two drivers not working: E0 and E1.
I am hesitant to try the motor on a working axis! But I will test it now.

I am using a Replistruder. I got the config.g file from a research paper.

Here are some pics of the board:

I also get this error when nothing is plugged into the drivers

@Phaedrux So I tried another motor on the same driver and got the same error. I mapped the extruder to another driver and got the same error. Tried a new motor on the new driver and same error.

Here is my config.g file:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue Apr 06 2021 11:31:03 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"HartingsLabFlashforge"                      ; set printer name
M555 P1


; Network

M552 S2 ; Turn network on in access point mode


; Drives
M569 P0 S0                              ; physical drive 0 goes forwards
M569 P1 S1                              ; physical drive 1 goes forwards
M569 P2 S1                              ; physical drive 2 goes forwards
M569 P3 S1                              ; EXTRUDER physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                        ; set drive mapping
M350 X64 Y64 Z16 E16 I1                 ; configure microstepping with interpolation
;M92 X376.48 Y376.48 Z400.00 E15360.00       ; set steps per mm
;M92 X378.37 Y380.41 Z403.83 E15360.00       ; set steps per mm
M92 X377.46 Y380.41 Z403.83 E15360.00       ; set steps per mm

M566 X180.00 Y180.00 Z60.00 E6.00     ; set maximum instantaneous speed changes (mm/min)
M203 X1800.00 Y1800.00 Z600.00 E60.00 ; set maximum speeds (mm/min)
M201 X150.00 Y150.00 Z150.00 E15.00     ; set accelerations (mm/s^2)
;M566 X600.00 Y600.00 Z60.00 E6.00     ;FAST set maximum instantaneous speed changes (mm/min)
;M203 X6000.00 Y6000.00 Z600.00 E60.00 ;FAST set maximum speeds (mm/min)
;M201 X600.00 Y600.00 Z150.00 E15.00   ;FAST set accelerations (mm/s^2)

M906 X550 Y550 Z450 E1100 I70           ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X105 Y150 Z50 S0                  ; set axis maxima

; Endstops
M574 X2 S1 P"!xstop"                     ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"!ystop"                     ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"!zstop"                     ; configure active-high endstop for high end on Z via pin zstop

; Heaters
M140 H-1                                ; disable heated bed (overrides default heater mapping)

; Fans

; Tools
M563 P0 D0                        ; define tool 0
G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

My M122:

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.4 (2022-10-20 16:17:41) running on Duet WiFi 1.02 or later
Board ID: 0JD2M-9F8TA-GJ4TD-6J1D6-3SD6M-16PQ6
Used output buffers: 1 of 26 (26 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 74320 of which 0 recycled
Never used RAM 13828, free system stack 140 words
Tasks: NETWORK(ready,15.4%,257) HEAT(notifyWait,0.0%,388) Move(notifyWait,0.0%,322) MAIN(running,83.6%,438) IDLE(ready,1.0%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:03:12 ago, cause: software
Last software reset at 2022-11-13 15:51, reason: User, GCodes spinning, available RAM 13828, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Step timer max interval 0
MCU temperature: min 29.7, current 30.1, max 30.8
Supply voltage: min 24.4, current 24.7, max 25.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 3709 queued, 3709 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min 0
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2022-11-13 15:55:05
Cache data hit count 4294967295
Slowest loop: 7.67ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 6.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 3, maxWait 49999ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 2, completed 2, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 2], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 13.35ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Network state is active
WiFi module is providing access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.27
WiFi MAC address a6:e5:7c:03:da:75
WiFi Vcc 3.36, reset reason Power up
WiFi flash size 2097152, free heap 24896
WiFi IP address 192.168.0.1
Connected clients 1
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

Hello, I just wired up my duet to a new printer and have successfully homed x,y,z axes. I am now trying to test my extruder motor. I am running a macro with

T0
G1 E10 F60

When I run this macro, I get the following error from the console:

Warning: Driver 3 warning: phase A may be disconnected, phase B may be disconnected

It will repeat this error about 20 times in the span of a second and there is no movement by the extruder motor. I have checked and replaced all of the wiring and connections. Not sure what the issue might be?

Thanks, Ben