Hello guys,

Anyone have this problem?
What happened is the print start off leaning to one side until next solid layer… Start by leaning to one side and when the next solid layer it start to go straight if there is a solid layer it start to leaning again???

What i have notice is:
M555 P1; It start straight and when there is a solid layer it start to leaning
M555 P0; It start leaning and when there is a solid layer it start to go straight

Things that i have do:

• checked every belt and pulley ( use marker to check the alignment)
• Use a dial to check every single axis if step per mm is accurate? ( 160step/mm , 0.98mm to 1.02mm)

I use simplify3d as my slicer. Can someone please give me a clue on this it is so frustrating maybe i did something wrong but i just couldn't figure it out.

Here is the link to the image: https://ibb.co/i8RLjQ

Hello,
I just install my duet wifi and also upgrade it to 1.19 firmware.
I tried to home all axis x,y,z and i notice there is a problem with it.

If x and y hit home first z will stop moving ==> homing failed on z
if x and z hit home first y will stop moving ==> homing failed on y
if y and z hit home first x will stop moving ==> homing failed on x

Here is my delta homing file:
G91 ; use relative positioning
G1 S1 X300 Y300 Z300 F1000 ; move all carriages up 300mm, stopping at the endstops
G1 S2 X-5 Y-5 Z-5 ; move all towers down 5mm
G1 S1 X8 Y8 Z8 F500 ; move towers slowly up 8mm, stopping at the endstops
G1 S2 X-5 Y-5 Z-5 F1000 ; move carriages down 5mm
G90

Here is my endstop section in config.g
; Endstops
M574 X2 Y2 Z2 S1 ; Define active high microswitches
M558 P1 X0 Y0 Z0 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
M557 R130 S20 ; Define mesh grid

Anyone have this problem??? Thanks you!

I also tried to move the motor from pointerface. Nothing works except home X axis button. So I dont think is a connection problem.

So i just set the M569 P8 S1 R0 T2; in the config.g which the motor is not energize the first time. I try to move it but it still not moving?

I have tried the M569 command. The only thing effect is the motor on and off.
If i use:
M569 P8 S1 R1 T2; the motor stay on

and if i use
M569 P8 S1 R0 T2; the motor stay off

I assuming the enb signal is wroking however the other is not that is what confusion me.

Hi guys im trying to remap x axis to different driver since im using external driver?

Im connecting the x motor to driver 8:
PUL-, ENB-, DIR- –-- GROUND
PUL+ ---- EXPANSION PIN 20
ENB+ ---- EXPANSION PIN 22
DIR+ ---- EXPANSION PIN 21

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 0 goes forwards
M569 P5 S1 ; Drive 1 goes forwards
M569 P6 S1 ; Drive 2 goes forwards
M569 P7 S1 ; Drive 3 goes forwards
M569 P8 S1 R1 T10; Drive 3 goes forwards
M584 X8 Y6 Z7 E:0:1:2:3:4:5 ; Driver 5 controls the X motor, 6 controls Y, 7 control Z motors, 3 control E motors
M350 E32 I0 ; Configure microstepping without interpolation
M350 X32 Y32 Z32 I1 ; Configure microstepping with interpolation
M92 X160 Y160 Z160 E837 ; Set steps per mm
M566 X1200 Y1200 Z1200 E3000 ; Set maximum instantaneous speed changes (mm/min)
M203 X39960 Y39960 Z39960 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1500 ; Set accelerations (mm/s^2)
;M906 X1800 Y1800 Z1800 E1500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

I could not get X axis to move using the Machine Control on the web interface?
Can someone help me how to do this? Thanks!