@button hi. what is the M669 G Code for this kinematics. thx
Posts made by Cobalt
-
RE: Dual markforged kinematicsposted in General Discussion
-
RE: PanelDueFirmware 3.2.6 releasedposted in PanelDue
@wilriker
now added this line to config.g M575 P1 B57600 S1. but bunch of stuff popping up at start. like (tool not selected) and more. but after that works . -
RE: PanelDueFirmware 3.2.6 releasedposted in PanelDue
@wilriker ```
code_text; executed by the firmware on start-up ; ; General preferences M80 G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"My Printer" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M584 X4 Y1 Z2:8:9 U7 E0:3:5:6 ; Driver Remap M569 P0 S1 ; Drive 0 goes forwards E1 M569 P1 S1 ; Drive 1 goes forwards Y M569 P2 S1 ; Drive 2 goes forwards Z M569 P3 S0 ; Drive 3 goes backward E2 M569 P4 S1 ; Drive 4 goes forwards X M569 P5 S1 ; Drive 5 goes forwards E3 M569 P6 S0 ; Drive 6 goes backward E4 M569 P7 S0 ; Drive 7 goes backward U M569 P8 S1 ; Drive 8 goes forwards z2 M569 P9 S1 ; Drive 9 goes forwards z3 M350 X16 U16 Y16 Z16:16:16 E16:16:16:16 I1 ; Configure microstepping with interpolation M92 X80.00 U80.00 Y80.00 Z1600.00:1600.00:1600.00 E424:424:424:424 ; Set steps per mm M566 X600.00 U600.00 Y600.00 Z24.00 E300:300:300:300 ; Set maximum instantaneous speed changes (mm/min) Jerk M203 X30000.00 U30000.00 Y30000.00 Z600.00:600.00:600.00 E3600.00:3600.00:3600.00:3600.00 ; Set maximum speeds (mm/min) M201 X3000.00 U3000.00 Y3000.00 Z120.00:120.00:120.00 E10000.00:10000.00:10000.00:1000.00 ; Set accelerations (mm/s^2) M906 X1000.00 U1000.00 Y1100.00 Z1100.00:1100.00:1100.00 E1000.00:1000.00:1000.00:1000.00 I50 ; Set motor currents (mA) and motor idle factor in per cent ;M84 S30 ; Set idle timeout ; Set idle timeout ; Axis Limits M208 X-270.2 U-225 Y-175 Z0 S1 ; Set axis minima M208 X225 U270.2 Y175 Z325 S0 ; Set axis maxima ; Endstops M574 X1 S1 P"!e1stop" ; configure active-low endstop for low end on X via pin E1 stop M574 U2 S1 P"!duex.e4stop" ; configure active-low endstop for low end on u via pin E4 stop M574 Y2 S1 P"!ystop" ; configure active-low endstop for high end on Y via pin Y stop M574 Z1 S2 ; configure Z-probe endstop for low end on Z Z axis Lead screw M671 X0:-320:320 Y238:-218:-218 S3 ; Z-Probe ;M558 P5 I0 R0.4 C"zprobe.in+zprobe.mod" H5 F1200 ; set Z probe type to effector and the dive height + speeds ;M558 P1 I1 F400 R1 T30000 A4 S-1 B1 C"zprobe.in" ; Analog M558 P8 I1 F400 R1 T30000 A4 S-1 B1 C"!zprobe.in+zprobe.mod" ; Digital (((((((((((Piezo)))))))))))) ;M558 P1 F300 H5 T30000 A3 S-1 C"zprobe.in+zprobe.mod" ; IR Probe G31 X0 Y0 U0 Z-0.15 P500 ; set Z probe trigger value, offset and trigger height M557 X-225:225 Y-170:170 P3:3 ; define mesh grid ; Heaters BED M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S100 ; set temperature limit for heater 0 to 100C M140 H0 ; map heated bed to heater 0 M307 H0 A171.3 C495.7 D0.8 S1.00 V24.2 B0 ; disable bang-bang mode for the bed heater and set PWM limit HEATER 1 M308 S1 P"e0temp" Y"thermistor" T100000 B4618 C5.127269e-8 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 A397.8 C226.9 D8.1 S0.90 V24.2 B0 ; PID HEATER 2 M308 S2 P"duex.e2temp" Y"thermistor" T100000 B4618 C5.127269e-8 ; configure sensor 2 as thermistor on pinduex.e2temp M950 H2 C"duex.e2heat" T2 ; create nozzle heater output on duex.e2heat and map it to sensor 2 M143 H2 S280 ; set temperature limit for heater 2 to 280C M307 H2 A329.2 C199.0 D6.6 S0.90 V24.2 B0 ; PID ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P2 S1 H-1 T45 X0.3 ; set fan 2 value. Thermostatic control is turned off M950 F3 C"duex.fan3" Q500 ; create fan 3 on pin duex.fan3 and set its frequency M106 P3 S0 H-1 ; set fan 3 value. Thermostatic control is turned OFF M950 F4 C"duex.fan4" Q500 ; create fan 4 on pin duex.fan3and set its frequency M106 P4 S1 H2 T45 ; set fan 4 value. Thermostatic control is turned on M950 F7 C"duex.fan7" Q500 ; create fan 7 on pin duex.fan3and set its frequency M106 P7 S1 H-1 T45 x0.3 ; set fan 7 value. Thermostatic control is turned off ; Tools PTool number D Extruder drive(s) H Heater(s) F Fan(s) Tool 0 M563 P0 D0 H1 F0:1 ; Tool 0 uses extruder 0, heater 1 fan 0 and 1 G10 P0 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures Tool 1 M563 P1 D1 H1 F0:1 ; Tool 1 uses extruder 1, heater 1 fan 0 and 1 G10 P1 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures Tool 2 M563 P2 D2 H2 X3 F3:4 ; Tool 2 uses extruder 3 and heater 2 and maps X to U, use fan 3:4 as the print cooling fan G10 P2 Y-0.1 U0 Z0 S0 R0 ; set tool 1 offsets and temperatures Tool 3 M563 P3 D3 H2 X3 F3:4 ; Tool 3 uses extruder 3 and heater 2 and maps X to U, use fan 3:4 as the print cooling fan G10 P3 Y-0.1 U0 Z0 S0 R0 ; set tool 1 offsets and temperatures Tool 4 copy M563 P4 D0:1:2:3 H1:2 X0:3 F1:1 ; tool 4 uses both extruders and hot end heaters, maps X to both X G10 P4 X50 Y0 U-50 S0 R0 M567 P4 E1:1 M302 S120 R110 ; Allow extrusion starting from 120°C and retractions already from 110°C ; Custom settings are not configured ; Miscellaneous``` code_text M122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2-beta4.1 running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DGM-9T6BU-FG3S8-6JTDG-3S86T-TBKZD Used output buffers: 3 of 24 (15 max) === RTOS === Static ram: 24188 Dynamic ram: 102504 of which 40 recycled Never used RAM 3316, free system stack 191 words Tasks: NETWORK(ready,187) HEAT(blocked,308) DUEX(blocked,35) MAIN(running,450) IDLE(ready,20) Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:03:15 ago, cause: power up Last software reset time unknown, reason: User, GCodes spinning, available RAM 3316, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN Error status: 0x00 MCU temperature: min 27.5, current 32.1, max 32.4 Supply voltage: min 0.1, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: position 0, standstill, SG min/max not available Driver 1: position 0, standstill, SG min/max not available Driver 2: position 0, standstill, SG min/max not available Driver 3: position 0, standstill, SG min/max not available Driver 4: position 0, standstill, SG min/max not available Driver 5: position 0, standstill, SG min/max not available Driver 6: position 0, standstill, SG min/max not available Driver 7: position 0, standstill, SG min/max not available Driver 8: position 0, standstill, SG min/max not available Driver 9: position 0, standstill, SG min/max not available Driver 10: position 0 Driver 11: position 0 Date/time: 2020-12-16 18:25:00 Cache data hit count 253203812 Slowest loop: 5.11ms; fastest: 0.13ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 1.2ms, write time 0.0ms, max retries 0 === Move === FreeDm 169 (min 169), maxWait 0ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.60ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.25beta0 WiFi MAC address 80:7d:3a:45:5b:22 WiFi Vcc 3.33, reset reason Turned on by main processor WiFi flash size 4194304, free heap 26920 WiFi IP address 192.168.1.42 WiFi signal strength -62dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 === DueX === Read count 1, 0.31 reads/min -
RE: PanelDueFirmware 3.2.6 releasedposted in PanelDue
Cobalt
Cobalt 15 Dec 2020, 10:18hi. updated my paneldue 7 v3 to 3.2.5 after update everything works but when i turn off and on the printer it won't connect . reset not help . but when update again its works until off/on
rrf 3.2b4.1
now same problem with 3.2.6
-
RE: PanelDueFirmware 3.2.5 releasedposted in PanelDue
hi. updated my paneldue 7 v3 to 3.2.5 after update everything works but when i turn off and on the printer it won't connect . reset not help . but when update again its works until off/on
rrf 3.2b4.1
-
RE: compiling paneldue firmwareposted in Firmware developers
hi i have same setup as you and same warnings. when i flash the firmware everything is ok