Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Computiger
    • Profile
    • Following 0
    • Followers 0
    • Topics 15
    • Posts 61
    • Best 1
    • Controversial 0
    • Groups 0

    Computiger

    @Computiger

    1
    Reputation
    1
    Profile views
    61
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Computiger Unfollow Follow

    Best posts made by Computiger

    • RE: Motor movement issue

      I tried wir 2.2A Motor Current. Motors run a bit hot during print. Wasn‘t diffrent.
      Also, I tested diffrent motors w/o changing the issue.

      Next week I will get a new Power Supply with 24v to change the whole system to this voltage.

      I will reply my experience

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger

    Latest posts made by Computiger

    • RE: BLTouch + additional servo

      I´ve just tried two other servo´s, these ones run fine like accepted.
      They are much cheaper than the 1st one. I have to check the wire.

      Thanks

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • RE: BLTouch + additional servo

      @dc42 said in BLTouch + additional servo:

      mean PWM4

      I mean PWM4

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • RE: BLTouch + additional servo

      using that servo
      Savox SC-0254MG

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • RE: BLTouch + additional servo

      like this over command line:

      M280 P1 S150
      
      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • BLTouch + additional servo

      I´m trying to set an servo for my tool changer (something like Prusa MMU) but the config for servo isn´t that easy for me.

      My Setup:
      Duet Wifi
      Duex5
      BLTouch
      miniServo

      • BLTouch is running for Z-probe and connected to Heater 5 of duex5
      • the servo I´d like to control is connected to Heater 4 of duex5

      The BLTouch is running in z probe w/o any issues but the other servo doesn´t move if I want

      M950 S0 C"duex.pwm5"                    ; create servo pin 0 for BLTouch (default from Config Tool)
      M950 S1 C"duex.pwm4"                    ; additional servo                        
      

      I guess my thinking isn´t correct. Please help me to understand how it works

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • RE: wrong screen on 7 inch Display

      sounds good, thanks

      posted in PanelDue
      Computigerundefined
      Computiger
    • RE: 12V PWM Fan on 24V Duet Wifi

      thanks 🙂

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • 12V PWM Fan on 24V Duet Wifi

      is it possible to use a 12V Fan on DuetWifi if main voltage is 24V?

      I have read an older topic and in that topic was described if I use 12V fans only I can take off the V-Fan Jumper and can connect +12V direct to the middle pin, is it right?

      0_1563045571219_Bildschirmfoto 2019-07-13 um 21.11.48.png

      posted in Duet Hardware and wiring
      Computigerundefined
      Computiger
    • RE: wrong screen on 7 inch Display

      any suggestions?

      posted in PanelDue
      Computigerundefined
      Computiger
    • RE: wrong screen on 7 inch Display

      yes, the toolbuttons ar in front of the macros. But if I press one of the Tools 2 till 5 the macro button is pressed insted of the tool

      posted in PanelDue
      Computigerundefined
      Computiger