Posts made by Dmitry Black

@dc42 OK thanks! I will try to contact the seller.

the results of M122 after errors

Static ram: 100104
Dynamic ram: 112588 of which 0 recycled
Never used RAM 31012, free system stack 180 words
Tasks: NETWORK(ready,204) HEAT(delaying,300) CanReceiv(notifyWait,944) CanSender(notifyWait,371) CanClock(delaying,334) TMC(delaying,105) MAIN(running,426) IDLE(ready,20) AIN(notifyWait,266)
Owned mutexes:
=== Platform ===
Last reset 00:07:24 ago, cause: power up
Last software reset at 2021-04-18 20:27, reason: User, GCodes spinning, available RAM 32044, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU revision 3, ADC conversions started 526376, completed 526375, timed out 0, errs 0
Step timer max interval 127351
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 11, reads 18881, writes 0, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 11, reads 18881, writes 0, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 18881, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 18882, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 18881, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-04-20 00:18:28
Cache data hit count 856128979
Slowest loop: 2994.35ms; fastest: 0.13ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 199.9ms, write time 119.5ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 3269, send timeouts 3269, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 6906.69ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.24beta2-05b1
WiFi MAC address f4:cf:a2:67:71:21
WiFi Vcc 3.36, reset reason Power up
WiFi flash size 2097152, free heap 24688
WiFi IP address 192.168.31.80
WiFi signal strength -54dBm, mode none, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

Hello!I updated my printer with a new board (Duet 3 mini 5+) and ran into a problem. When I try to upload a file, the process is interrupted, and starts again once. Then I get a few errors and lose connection with the DWC until I restart my Duet.
The 12864 screen also loses files and stops displaying the menu.
But sometimes it is possible to upload small files right after the board is turned on.
I've tried different firmwares including Release 3.2.2, 3.3beta2
Also i tried different memory cards, including the high-speed sandisk ultra 32gb from gopro.
My board Duet 3 mini 5+, rev.0.5, purchased from filafarm.de

@Phaedrux Hello! I seem to be having the same problem. When I try to upload a file, the process is interrupted, and starts again once. Then I get a few errors and lose connection with the DWC until I restart my Duet.
The 12864 screen also loses files and stops displaying the menu.
But sometimes it is possible to upload small files right after the board is turned on.
I've tried different firmwares including Release 3.2.2, 3.3beta2
My board Duet 3 mini 5+, rev.0.5, purchased from https://www.filafarm.de/