Posts made by eder

thanks monster for information i look times

hello, has gotten better but the problem remains despite: - ((

@eder said in Hi at this please help:

yes i have ok i try

extruder has been calibrated but the error remains despite what remains.
Thanks Eder

@PaulHew said in Hi at this please help:

extruder calibration

Hello, thank you for helping me, extruder has been calibrated

Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Feb 21 2020 16:39:28 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Mister" ; set printer name

M667 S1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

M555 P1 ; Set firmware compatibility to look like Marlinxxxxxxxxxxxxx

; Drives
M569 P0 S0 ;E physical drive 0 goes forwards
M569 P1 S0 ;X physical drive 1 goes forwards
M569 P2 S1 ;Y physical drive 2 goes forwards
M569 P3 S1 ;Z physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I0 ; configure microstepping without interpolation
M92 X80 Y80 Z793.6 E98.03 ; set steps per mm
M566 X2000 Y2000 Z20 E1000 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z600.00 E6000.00 ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z200.00 E800.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S120 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y260 Z310.40 S0 ; set axis maxima

; Endstops
M574 Z2 S0 P"zstop" ; configure active-high endstop for high end on Z via pin zstop
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"zprobe.in+zprobe.mod" H5 F400 T9000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z4.45 ; set Z probe trigger value, offset and trigger height
M557 X1:300 Y1:260 S60 ; define mesh grid

; BED
M308 S0 P"bedtemp" Y"PT1000" X500 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M307 H0 A269.0 C392.3 D2.9 B0
M305 P0 T100000 X500 R4700
M140 H0 ; map heated bed to heater 0

; HOTEND
M308 S1 P"e0temp" Y"PT1000"T100000 X501 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1 ; disable bang-bang mode for heater and set PWM limit
M307 H1 A438.8 C250.7 D5.7 B0
M305 P1 T100000 X501 R4700

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H1 T100 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 F0:1 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Miscellaneous
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool

Hi at this please help, I have a problem
how to set up cube printing
I have duet wifi 2
RepRap

I have Duet Wifi 2
Sofware RepRap