Well, that was simple. Thank you.

Hello everyone,

with the help of this thread Using Multiple Bed Heaters I have set up my dual zone heated bed. I'm using 2 AC heaters controlled via 2 SSR's.

The heater on heated bed output (H0) is working well, but when heating the E3 (H4) I get "Error: Heating fault on heater 4, temperature rising much more slowly than the expected 1.8°C/sec". When connecting the heater to H0 it's getting warm, also when I connect the thermistor to the H0 thermistor input I see that it's registering a rising temperature well faster than the 1.8°C/sec.

So my guess is that the H4 heater doesn't get the thermistor signal??

; ============= Bed Heaters =============

M140 P0 H0
M140 P1 H4

M305 P0 R4700 T100000 B3950
M305 P4 R4700 T100000 B3950

M143 H0 S120
M143 H4 S120

M570 H0 S1000
M570 H4 S1000

I really hope there is no silly mistake I made

Firmware version 2.01 was installed, I updated to 2.02 but the problem still persists.
I tested some more things. When only one motor (doesn't matter which) is moving the carriage, then the problem is still the same.

But I noticed, only about 5mm of travel is lost. If i move x +100mm it moves 95mm and following with x -100mm the slider stops at 0 again. Same with 50mm and 10mm moves. It moves about 3-5mm stops for some milliseconds and then continues to move the rest of the travel.
All moves following in the same direction are perfectly executed.

I made a short video to show the problem

First of all, happy new year!

I'm having a problem with my setup of the Duet2 WiFi Board. I have a X-axis with two Nema23 stepper motors moving the Y-axis in parallel via 2 belts separate belts. I use the drivers 0 and 4 for the motors on the X-axis. I hope you can visualize my setup.

So the problem is, when I want to move the X-axis in a new direction, then the motor skips or stalls (not make a noise) on the first move. Every move in the same direction works fine. When I change direction again, same happens on the first move and the following in the same direction work perfectly.
Example:
x +10mm - skips and only moves 5mm
x +10mm - works fine and moves 10mm
x -10mm - skips and only moves 5mm
x -10mm - works fine and moves 10mm

No other axis are affected and work perfectly.

I've played with acceleration, micro-stepping, instantaneous speed changes, belt tension.
The thing is, when I disconnect the belt from the Y-axis slider and the belt moves on its own without moving the Y-axis then this problem does not occur. This problem does also not occur when using a different board with Pololu drivers.

I've added the config below, but I'm not finished with the setup.
I hope someone can help me.

Have a nice day

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Wed Dec 19 2018 20:23:10 GMT+0100 (Central European Standard Time)

; General preferences
G90                                         ; Send absolute coordinates...
M83                                         ; ...but relative extruder moves

; Network
M550 P"----"                                ; Set machine name
M551 P"----"                                ; Set password
M552 S1                                     ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1                                  ; Enable HTTP
M586 P1 S0                                  ; Disable FTP
M586 P2 S0                                  ; Disable Telnet

; Drives
M584 X0:4 Y1 Z2 E3
M569 P0 S0                                  ; Drive 0 goes backwards
M569 P1 S0                                  ; Drive 1 goes backwards
M569 P2 S0                                  ; Drive 2 goes backwards
M569 P3 S1                                  ; Drive 3 goes forwards
M569 P4 S1				    ; Drive 4 goes forwards
M350 X32 Y32 Z32 E16 I0                     ; Configure microstepping without interpolation
M92 X64.00 Y88.89 Z1600.00 E415.00          ; Set steps per mm
M566 X10.00 Y900.00 Z12.00 E120.00         ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00     ; Set maximum speeds (mm/min)
M201 X10.00 Y500.00 Z20.00 E250.00         ; Set accelerations (mm/s^2)
M906 X2400.00 Y1000.00 Z1500.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                            ; Set axis minima
M208 X780 Y450 Z800 S0                      ; Set axis maxima

; Endstops
M574 X1 Y1 S1                               ; Set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                       ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:11 Y15:195 S20                     ; Define mesh grid

; Heaters
M140 H-1                                    ; Disable heated bed
M305 P1 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                    ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1                    ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1                               ; Define tool 0
G10 P0 X0 Y0 Z0                             ; Set tool 0 axis offsets
G10 P0 R0 S0                                ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured