Posts made by Freddy1455

got it working, by using M558 P1 R0.4 F1000 X0 Z0

i checked my crimps and that that resister was there and still 1000 in my z.
https://imgur.com/a/sp6VA

i updated the firmware to 1.19 checked the wiring, my z is still at 1000.
i can send a M672 S131:131 and it blinks 5 times like its receiving commands.

cool, knowing that im guessing i miswired it, i pulled the 6 pin and its still at 1k

https://imgur.com/a/OJasg

is my wiering correct?

checked my wire resistance and no wires are crossed or broken.

my z probe in the web interface is stuck at 1000, when i tap the effector the strain Gage light turns on like its working. im enclosing config.g my fw version is 1.19-b6 (2017-05-19) and im using the 0.8.5 Ethernet version of the duet. do u guys have any ideas about whats going on?

; Configuration file for Duet 0.8.5 (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon May 22 2017 19:19:15 GMT-0500 (Central Daylight Time)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M665 L494.762 R249.273 H371.713 B150.0 X0.215 Y-0.498 Z0.000
M666 X-0.309 Y0.608 Z-0.299 A0.00 B0.00
M208 Z-10 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S0 ; Define active low and unused microswitches
M558 P5 R0.4 F1000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R150 S30 ; define a grid with the specified radius and spacing (for delta printers)

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M92 X80 Y80 Z80 E396.23 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PMy printer ; Set machine name
M540 PBE:EF:DE:AD:FE:ED ; Set MAC address
M552 P192.168.5.202 S1 ; Enable network and set IP address
M553 P255.255.255.0 ; Set netmask
M554 P192.168.5.1 ; Set gateway
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured
M501