@Phaedrux `M122
code_text
``
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.1 (2024-04-19 14:30:55) running on Duet 3 MB6HC v1.02 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3T0-6J1DG-3SJ6T-1B3HB
Used output buffers: 5 of 40 (29 max)
=== RTOS ===
Static ram: 155208
Dynamic ram: 123480 of which 0 recycled
Never used RAM 67304, free system stack 204 words
Tasks: NETWORK(1,ready,37.2%,183) ETHERNET(5,nWait 7,0.2%,317) HEAT(3,nWait 6,0.0%,325) Move(4,nWait 6,0.0%,336) CanReceiv(6,nWait 1,0.0%,797) CanSender(5,nWait 7,0.0%,334) CanClock(7,delaying,0.0%,348) TMC(4,nWait 6,9.3%,56) MAIN(1,running,53.1%,105) IDLE(0,ready,0.2%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:01:19 ago, cause: power up
Last software reset at 2025-01-03 17:25, reason: User, Gcodes spinning, available RAM 69368, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 13.1, current 24.1, max 24.1
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.4, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 8, reads 43649, writes 16 timeouts 0
Driver 1: standstill, SG min n/a, mspos 8, reads 43649, writes 16 timeouts 0
Driver 2: standstill, SG min n/a, mspos 8, reads 43649, writes 16 timeouts 0
Driver 3: standstill, SG min n/a, mspos 8, reads 43649, writes 16 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 43649, writes 16 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 43650, writes 16 timeouts 0
Date/time: 2025-01-04 20:14:49
Slowest loop: 5.06ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 5.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 725, received 654, lost 0, errs 49, boc 0
Longest wait 1ms for reply type 6018, peak Tx sync delay 7908, free buffers 50 (min 49), ts 398/397/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 5.93ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 1 0 0
Socket states: 5 5 2 2 2 0 0 0
=== WiFi ===
Interface state: disabled
Module is disabled
Failed messages: pending 0, notrdy 0, noresp 0
Socket states: 0 0 0 0 0 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
code_text M98 P"config.g"
Tool 0 mix ratios: 1.000:0.000
Tool 1 mix ratios: 1.000:0.000
M98 P"config.g"
HTTP is enabled on port 80
