I managed to do an autotune and it worked fine then m500 to save which I didn't do before then set it to heat up and it heated up fine.
I've been installing a linear rail setup on my x axis so I have to wire everything back up and see.
When it was doing it it got to 80c in decent time but I guess it wasnt fast enough for the board and faulted. Hopefully everything is ok now since I really don't wanna resort to using a 22 dollar board.
Still doesnt work. Running through external mosfets it falls on its face around 80c.
@bearer said in Duet 2 maestro problems:
what does
M307 H1output? (or H2 if using E1)@humanxv2 said in Duet 2 maestro problems:
I ordered a skr 1.3 marlin board I was gonna use and it doesnt like me much.
kinda ot but i think alex kenis recently posted a video suggesting there is a design flaw with the usb interface on those?
Yeah it stopped communicating with anything.
Doing the same thing with new parts. I ordered some external mosfet boards and see if they work.
I ordered a skr 1.3 marlin board I was gonna use and it doesnt like me much.
Still hitting around 80c and slows way down.
New heater cartridge on the way.
Plugged extruder into e1 and define is as a new tool using e1 gears and so far so good
Heater is in e1 and thermistor is in e1.
I changed the config to reflect this and the heater will not come on and the thermistor is showing 2000.
Heaters
M307 H0 B0 S1.00
M305 P0 T98801 B4185 R2200
M143 H0 S120
M305 P2 T1000000 B4725 C7.06e-8
M143 H2 S280
Put cartridge in that came with hot end and it heated fast until 80c then kinda fell on its face.
It's back in e0 now. If I put it in e1 do i still use H1?
Auto tune keeps stopping saying the temp is rising too slow. Fans are off and I did M303 H1 P1 and it is still coming up real slow. Either it is coming up fine and the thermistor might be bad and not accurately reading the temp or the heater probe is bad. I switched the probe out earlier and put the stock one back in so I may put the other back in and try.
I have already ordered a new thermistor cartridge.
The heat block was a tad bit loose so I removed the heater cartridge and thermistor to tighten it a little and put them back. I can't tighten it real tight cause the angle the wires end up at, they run into the cooling ducts.
The thermistor reads the temp correctly when plugged into e0 but read 2000c when plugged into e1.
Got everything working. Started a print the other day and I noticed that when it got the the upper layers it was printing in midair and not laying down filament.
I pulled the nozzle and it was clogged so I unclogged it and put it back on and now the heat is faulting out saying the heat is rising too slow. I switched the motor and heats from e0 to e1 and the heat is still faulting.
I moved the switch for y so that it's there for the probe to touch
@bearer said in Duet 2 maestro problems:
@humanxv2 said in Duet 2 maestro problems:
now z will not home. I don't have the z stop hooked up since I'm using a bltouch and I have to touch the probe to get the motor to stop.
?
Homing is achieved by moving until it hits a endstop, and setting the axis to a known value. The homing is moving until it trips the endstop or probe. So you need to let the motor run until the probe touches the bed, or add a end stop.
Well the bed is all the back at home so there's it's not there for the probe to touch.
Ok so it makes no sense but I read the reviews of the cables I got and one guy said he had to swap the green and red wires so i did that and it worked. Now the errors are gone with the motors but now z will not home. I don't have the z stop hooked up since I'm using a bltouch and I have to touch the probe to get the motor to stop.
Have tried 3 cables now. Checked with meter. If I power up with nothing plugged in I get no errors. If I plug the cable in and don't plug it into motor it gets errors so it points to being the cable but I cannot find anything wrong.
Even after i figure this part out i still have a heat fault and a screen that doesn't work. Pretty close to throwing it in the trash since it's been nothing but problems.
Whenever I swap wires whatever ends up with the all black OEM cable works fine. The new wires are color coded and the connector that plugs into the motor is the same and wires are in the same slots. I cut the old board side connectors off and crimped new pins for the correct connectors. I have tried 2 new cables on it.
This is maddening
Wiring has been checked. I tried it with another motor and it still does it. It doesn't do it with the wire unplugged.
It had a new wire since the z axis cable got lost during the process and I even made a new one just in case. I'm gonna take the wire off of x and use it for a and see if it works.
And I still have to contend with the screen and the heat fault.
Thanks
Ok X had one if the wires come lose inside the connector so it is acting fine now and homing.
Still having ground fault on Z. Z will not move at all.
Tried several different menu files and nothing will display. Just a blue screen. Yesterday before firmware update screen showed a fault in line 3.
I have to change the config for the titan aero because it is showing a heater fault.
This is on an ender 3 pro with a titan aero that I installed before I wired the board. I changed connectors and was very careful.
Loaded the config files and fired it up and had a menu error.
I finally connected with yat and updated firmware and then connect with web control. Now the screen is blank and I'm getting ground short errors. Y axis seemed to home and wont move anymore. X wants to go left instead of right and is making an awful noise. Z will not do anything.
BLtouch probe flashes red.
Ready to chunk it all