Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. IvanG
    • Profile
    • Following 0
    • Followers 0
    • Topics 5
    • Posts 26
    • Best 2
    • Controversial 0
    • Groups 0

    IvanG

    @IvanG

    2
    Reputation
    1
    Profile views
    26
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    IvanG Unfollow Follow

    Best posts made by IvanG

    • hot bed without mosfet ender 3

      Hello I just bought a wifi duet for my ender 3, this printer comes with 24v hot bed, can I connect directly to the duetwifi without any mosfet?

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: How to create a mesh for Bltouch

      @t3p3tony said in How to create a mesh for Bltouch:

      @ivang from a noise perspective running x16 interpolated to 256 and running x256 is functionally the same. The only difference is that the driver is generating the intermediate steps. I could not tell a noise difference between the two during testing.

      I think maybe you do not have I1 in you M350 command ?

      Also note that interpolation only works on x16 (not for example x32 and x64)

      He is right I just put the end I1 and the noise is almost nonexistent, thank you very much.

      posted in Firmware installation
      IvanGundefined
      IvanG

    Latest posts made by IvanG

    • hot bed without mosfet ender 3

      Hello I just bought a wifi duet for my ender 3, this printer comes with 24v hot bed, can I connect directly to the duetwifi without any mosfet?

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      Sorry but I have them connected in series in ZA and ZB I do not know why I put it in parallel, I really have it connected in series, I do not understand why every time you go up and down the bed it stays at a different height, especially when I turn off and turn on the printer is a disaster the lead screw connected to the ZB is 5mm lower than the ZA and the spindle connected to the Extruder is 7 or 8 mm lower, although I raise them manually and the level again happens the same, my screws advance and nuts are from T8x8

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      I have manually leveled with the printer off and the problem remains exactly the same, I think I am going to try to put 2 advance screws instead of 3

      0_1524600500004_2018-04-24 (1).png

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      The engines for z are these:

      https://www.amazon.es/gp/product/B06XQWMDWT/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

      The maximum current they support is 1.7A

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      An image of the result of my bltouch probe0_1524597367605_2018-04-24.png

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      Thanks for your help my config.g is the following

      ; Configuration file for Duet WiFi (firmware version 1.20 or newer)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool on Sun Apr 08 2018 20:13:54 GMT+0200 (Hora de verano romance)

      ; General preferences
      G90 ; Send absolute coordinates...
      M83 ; ...but relative extruder moves

      M667 S1 ; Select CoreXY mode

      ; Network
      M550 PD-BOT ; Set machine name
      M552 S1 ; Enable network
      ;*** Access point is configured manually via M587
      M586 P0 S1 ; Enable HTTP
      M586 P1 S0 ; Disable FTP
      M586 P2 S0 ; Disable Telnet

      ; Drives
      M569 P0 S0 ; Drive 0 goes forwards
      M569 P1 S0 ; Drive 1 goes forwards
      M569 P2 S0 ; Drive 2 goes backwards
      M569 P3 S0 ; Drive 3 goes backwards
      M584 X0 Y1 Z2:3 E4 ; Apply custom drive mapping
      M350 X16 Y16 Z16 E16 I1 ; XYZ and E0 microstepping
      M92 X100 Y100 Z400 E420 ; Set steps per mm
      M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
      M203 X6000 Y6000 Z200 E1200 ; Set maximum speeds (mm/min)
      M201 X500 Y20 Z250 E250 ; Set accelerations (mm/s^2)
      M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; Set axis minima
      M208 X300 Y260 Z450 S0 ; Set axis maxima

      ; Endstops
      M574 X1 Y2 S0 ; X home to min. Y and Z home to max. Normally Closed limit switches.
      M574 Z2 S2 ; Define Z to use Probe. Home to Min

      ; Z-Probe
      M558 P9 X0 Y0 Z2 H5 F100 T4000 A10 R0.5 S0.008 ;Set Z probe type/mode 5. H=Dive Height. F=Speed the bed moves
      G31 X-19 Y-37 Z1.52 P25 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
      M557 X15:280 Y15:245 S30 ; Define mesh grid
      M376 H20 ;
      M375 ; Load heightmap.csv

      ; Heaters
      M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
      M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
      M143 H0 S120 ; Set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
      M143 H1 S280 ; Set temperature limit for heater 1 to 280C
      ; BLTouch - Heaters
      M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.

      ; Fans
      M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
      M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 ; Define tool 0
      G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
      G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

      ; Automatic saving after power loss is not enabled

      ; Custom settings are not configured

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Corexy 3 lead screws problem with height

      Hello when it is off if I can move them to level them, but every time I go up and under the bed each one is always at a different height, I am not using the automatic leveling of the bed, I understand that for this function the 3 advance screws they have to be connected in different divers, I use 2 in parallel.

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • Corexy 3 lead screws problem with height

      Hello I have a problem with my corexy printer I am using 3 lead screw 2 screws in parallel connected to the Z and 1 screw connected to the extruder, the spindles move up and down without problem, what happens when I do z homing each screw is at a height different, is there any way to solve this problem?

      I am using the duetwifi plate

      1_1524592032091_IMG_20180424_193936.jpg 0_1524592032091_IMG_20180424_193927.jpg

      posted in Duet Hardware and wiring
      IvanGundefined
      IvanG
    • RE: Bltouch goes down fast

      @dc42 said in Bltouch goes down fast:

      @ivang said in Bltouch goes down fast:

      @dc42 said in Bltouch goes down fast:

      If the problem is that the pin is dropping too fast after the probe triggers, either increase the travel speed (T parameter in M558), or change to P9 in the M558 command (which needs firmware 1.21 to work).

      Thank you try it, I have another problem that I just saw, when the XY axes move the 3 axes Z also turn very very slowly, because can this be ??

      That's normal if you have bed compensation enabled.

      I just want to use Bltouch to create the mesh at the time of printing, the strange thing is that if I move with the X axis 100mm the z axes also start moving, as I can disable so that the Z axes do not move when I move them. X and Y axes

      posted in IR Height Sensor
      IvanGundefined
      IvanG
    • RE: Bltouch goes down fast

      @dc42 said in Bltouch goes down fast:

      If the problem is that the pin is dropping too fast after the probe triggers, either increase the travel speed (T parameter in M558), or change to P9 in the M558 command (which needs firmware 1.21 to work).

      Thank you try it, I have another problem that I just saw, when the XY axes move the 3 axes Z also turn very very slowly, because can this be ??

      posted in IR Height Sensor
      IvanGundefined
      IvanG