Config.g

; Configuration file for Duet WiFi (firmware version 1.21)

; executed by the firmware on start-up

;

; generated by RepRapFirmware Configuration Tool v2 on Mon Jan 07 2019 13:59:59 GMT-0500 (Eastern Standard Time)

; General preferences

G90 ; Send absolute coordinates...

M83 ; ...but relative extruder moves

; Network

M550 P"Jester3D" ; Set machine name

M551 P"JOKER_ofshadows13!*E3: ; Set password*

M552 S1 ; Enable network

;** Access point is configured manually via M587

M586 P0 S1 ; Enable HTTP

M586 P1 S0 ; Disable FTP

M586 P2 S0 ; Disable Telnet

; Drives

M569 P0 S0 ; Drive 0 goes backwards

M569 P1 S0 ; Drive 1 goes backwards

M569 P2 S1 ; Drive 2 goes forwards

M569 P3 S0 ; Drive 3 goes backwards

M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation

M92 X80.00 Y80.00 Z400.00 E93.00 ; Set steps per mm

M566 X1200.00 Y1200.00 Z24.00 E300.00 ; Set maximum instantaneous speed changes (mm/min)

M203 X30000.00 Y30000.00 Z300.00 E300.00 ; Set maximum speeds (mm/min)

M201 X500.00 Y500.00 Z100.00 E5000.00 ; Set accelerations (mm/s^2)

M906 X400.00 Y400.00 Z400.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent

M84 S300 ; Set idle timeout

; Axis Limits

M208 X-5.5 Y0 Z0 S1 ; Set axis minima

M208 X235 Y235 Z260 S0 ; Set axis maxima

; Endstops

M574 X1 Y1 Z1 S1 ; Set active high endstops

; Z-Probe

M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch

M558 P9 H2.5 F120 T6000 ; Set Z probe type to bltouch and the dive height + speeds

G31 P500 X-31 Y0 Z0.6 ; Set Z probe trigger value, offset and trigger height

M557 X20:215 Y20:215 S20 ; Define mesh grid

; Heaters

M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0

M143 H0 S120 ; Set temperature limit for heater 0 to 120C

M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1

M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans

M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off

M106 P1 S1 I0 F500 H0 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

M106 P2 S1 I0 F500 H1:0 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools

M563 P0 D0 H1 ; Define tool 0

G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets

G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving

M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

Config-override.g

; This is a system-generated file - do not edit

; Heater model parameters

M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B1

M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H2 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H3 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0

M307 H7 A340.0 C140.0 D5.5 S1.00 V0.0 B0