Topics created by KenD

@KenD ```
code_text

; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.5.0-rc.3 on Sat Mar 02 2024 14:18:20 GMT-0500 (Eastern Standard Time) ;CAN BUS G4 S2 ; wait for expansion boards to start ; General M550 P"Core6" ; set hostname ; Accessories M575 P1 S0 B57600 ; configure PanelDue support ; Network M552 P192.168.9.240 S1 ; configure Ethernet adapter ;M586 P0 S1 ; configure HTTP ; Smart Drivers M569 P0.0 S0 D2 ; driver 0.0 goes forwards (X axis) M915 P0.0 S10 F0 R0 ; set StallGuard threshold M569 P0.1 S1 D2 ; driver 0.1 goes backwards (Y axis) M915 P0.1 S10 F0 R0 ; set StallGuard threshold M569 P0.2 S0 D2 ; driver 0.2 goes backwards (Z axis) M569 P0.3 S1 D2 ; driver 0.3 goes forwards (extruder 0) M569 P0.4 S0 D2 ; driver 0.4 goes backwards (Z axis) M569 P0.5 S0 D2 ; driver 0.5 goes backwards (Z axis) ; Motor Idle Current Reduction M906 I50 ; set motor current idle factor M84 S60 ; set motor current idle timeout ; Axes M669 K1 ; Configure Core XY Kinematics M584 X0.0 Y0.1 Z0.2:0.4:0.5 ; set axis mapping M671 X330:650:00 Y300:50:50 S2 ; Set the Z motor locations and max correction in mm M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation M906 X1000 Y1000 Z1000 ; set axis driver currents M92 X80 Y80 Z6405 ; configure steps per mm M208 X0:680 Y0:320 Z0:365 ; set minimum and maximum axis limits M566 X900 Y900 Z120 ; set maximum instantaneous speed changes (mm/min) M203 X9000 Y9000 Z500 ; set maximum speeds (mm/min) M201 X2000 Y2000 Z100 ; set accelerations (mm/s^2) ;M201.1 X500 Y500 ; set Acceleration while homing ; Extruders M584 E0.3 ; set extruder mapping M350 E16 I1 ; configure microstepping with interpolation M906 E1000 ; set extruder driver currents M92 E830 ; configure steps per mm M566 E150 ; set maximum instantaneous speed changes (mm/min) M203 E7000 ; set maximum speeds (mm/min) M201 E400 ; set accelerations (mm/s^2) ; Accelerometer M955 P120.0 I64 ; Add accelerometer on SZP with CAN address 120 and specify orientation ; Scanning Z probe M558 P11 C"120.i2c.ldc1612" F4000 T4000 ; set scanning Z probe as primary z probe and dive height M308 A"SZP coil" S10 Y"thermistor" P"120.temp0" ; thermistor on coil M558.2 S20 R146027 ; set drive current and reading offset G31 X24 Y0 Z2.5 ; set Z probe Offset and Trigger height ; Smart IR Probe ;M558 K0 P8 C"io3.in" H5 F200 T6000 ; configure to MODE 8 for IR Z PROBE and Probe this point 3 TIMES. On Duet 3, the IR probe is always in digital mode. ;G31 P475 X21 Y0 Z2.23 ; set Z probe trigger value, offset and trigger height ; Endstops ;M574 X2 S2 ; configure X axis high end endstop for SZP Accelerometer ;M574 Y1 S2 ; configure Y axis low end endstop for SZP Accelerometer ;M574 Z1 S2 ; configure Z axis low end endstop for SZP M574 X2 S3 ; configure X axis high end endstop for single motor stall M574 Y1 S3 ; configure Y axis low end endstop for single motor stall M574 Z1 S2 ; configure Z axis low end endstop for Z probe ; Mesh Bed Compensation M557 X5:320 Y5:670 S25:25 ; define grid for mesh bed compensation ; Sensors M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B3950 C7.06e-8 ; configure sensor #0 M308 S1 P"temp1" Y"thermistor" A"nozzle" T500000 B4723 C1.196220e-7 ; configure sensor #1 ;M308 S1 P"temp1" Y"pt1000" A"Nozzle" ; configure sensor #1 ;M308 S2 P"temp2" Y"thermistor" A"ambient" T100000 B3950 C7.06e-8 ; configure sensor #2 M308 S11 Y"mcu-temp" A"MCU" ; defines sensor 10 as MCU temperature sensor M308 S12 Y"drivers" A"Duet stepper drivers" ; defines sensor 11 as stepper driver temperature sensor ; Case fan - configure sensor 2 as temperature warning and overheat flags on the TMC2660 on Duet ; !!! Reports 0C when there is no warning, 100C if any driver reports over-temperature ; !!! warning , and 150C if any driver reports over-temperature shutdown ; Filament Run-Out Sensor M591 D0 P3 C"io8.in" S1 R50:150 L25.47 E3.0 ; Duet3D magnetic sensor(P3) for extruder drive 0(D0), connected to endstop input 3 (C3), tolerance 70 to 130%, 3mm comparison length(E3), ; L=Filament movement per complete rotation of the sense wheel, in mm S0= Disabled ; Heaters M950 H0 C"out0" T0 ; create bed heater #0 M143 H0 P0 T0 C0 S140 A0 ; configure heater monitor #0 for heater #0 M307 H0 R0.983 K3.090:0.000 D2.12 E1.35 S1.00 B0 ; configure model of heater #0 Bang-Bang mode M950 H1 C"out1" T1 ; create nozzle heater #1 M143 H1 P0 T1 C0 S285 A0 ; configure heater monitor #1 for heater #1 M307 H1 R2.608 K0.408:0.000 D3.88 E1.35 S1.00 B0 V24 ; configure model of heater #1 PWM Mode ; Heated beds M140 P0 H0 ; configure heated bed #0 ; Fans M950 F0 C"out3" ; create Part fans 24v 2 wire Fan #0 M106 P0 C"Part" S0 L0 X1 B0.5 ; configure fan #0 M950 F1 C"out2" ; create Tool Fan 24v 2 wire Fan #1 M106 P1 C"Tool" S0 B0.5 H1 T40 ; configure fan #1 M950 F2 C"out7" ; create MCU Fan 12v 2 wire. Fan #2 M106 P2 C"Case" S0 L0 X1 B0.5 T35 H12 ; configure fan #2 ; Tools M563 P0 S"Mosquito" D0 H1 F1 ; create tool #0 M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C ; Miscellaneous M501 ; load saved parameters from non-volatile memory T0 ; select first tool

@gloomyandy Thanks! I overlooked this. I had this right at one time but then my Config.G and Config.Bak got deleted due to the factory 2 test Macro still being on the SD card. Apparently the config file I used to restore it did not have that correction in it

@KenD Could it be that whatever hobbed bolt arrangement is used to grip the filament is slipping on the motor shaft? It would explain why you can hear the motors after the filament had stopped extruding.
For info, the only Quad I saw running a demo print was soooo slow. Maybe 5mm/sec extruder speed is the max that those tiny motors can do.