Posts made by Kiomatri

undefined

@droftarts Hey Ian, Thanks for your reply.
Sadly, that doesn't seem to fix the -3.00mm I get from performing the G30 S-1 command

(Also, I'm not constantly seeing 1000, that seems to do what it should)

undefined

Hello All,

I have the following hardware:

Genuine BLTouch v3.1
Duet3 6HC
Duet3 ex 3HC
Z Axis with 3 steppers

When executing the steps written in Test and calibrate the Z probe, I always get the message back "Probe stopped at -3.00mm" whatever I do.
Homing however, is no problem.

I increased / decreased the distance of the BLTouch with washers
(Between 10 to 6 mm from bottom of BLTouch to end of printhead)
I tried playing around with the Z trigger height
Checked the wiring of course

What am I doing wrong? I'm lost...

The following is my config.g:
(The {1}'s seem to be added by this site, I don't know where they are coming from...)

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Jul 29 2020 22:00:06 GMT+0200 (Midden-Europese zomertijd)

; General preferences
G90                                                ; send absolute coordinates...
M83                                               ; ...but relative extruder moves
M550 P"Monstro"                       ; set printer name

; Network
M551 P"******"
M552 P0.0.0.0 S1
M586 P0 S1
M586 P1 S0
M586 P2 S0

; Drives
M569 P0.0 S1
M569 P0.1 S0
M569 P0.2 S0
M569 P0.3 S1
M569 P0.4 S1
M569 P0.5 S1
M569 P1.0 S0
M569 P1.1 S0
M569 P1.2 S0

; set drive mapping
M584 X0.0:0.1 Y0.2:0.3 Z1.0:1.1:1.2 E0.4:0.5

; configure microstepping with interpolation
M350 X16:16 Y16:16 Z16:16:16 E16:16 I1

; set steps per mm
M92 X160.00 Y160.00 Z1600.00 E420.00:420.00

; set maximum instantaneous speed changes (mm/min)
M566 X900.00 Y900.00 Z200.00 E120.00

; set maximum speeds (mm/min)
M203 X6000.00 Y6000.00 Z800.00 E1200.00

; set accelerations (mm/s^2)
M201 X500.00 Y500.00 Z20.00 E250.00

; set motor currents (mA) and motor idle factor in per cent
M906 X1200 Y1200 Z1600 E1200 I30

; Set idle timeout
M84 S30

; Axis Limits
M208 X0 Y0 Z0 S1
M208 X550 Y500 Z740 S0

; Endstops
M574 X1 S1 P"!io0.in"
M574 Y1 S1 P"!io1.in"
M574 Z1 S2

; Z-Probe
M950 S0 C"io7.out"
M558 P9 C"^io7.in" H4 F120 T6000 R0.5
G31 P500 X-40 Y-10 Z1
M557 X15:545 Y5:495 P4

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138
M950 H0 C"out1" T0
M307 H0 B0 S1.00
M308 S1 P"temp1" Y"thermistor" T100000 B4138
M950 H1 C"out2" T1
M307 H1 B0 S1.00

; Fans
M950 F0 C"out4" Q500
M106 P0 S1 H1 T45
M950 F1 C"out5" Q500
M106 P1 S1 H1 T45

; Tools
M563 P0 S"ext1" D0 H0 F0
G10 P0 X0 Y0 Z0
G10 P0 R0 S0
M563 P1 S"ext2" D1 H1 F0
G10 P1 X0 Y31.3 Z0
G10 P1 R0 S0

; NeoPixels
M150 X1

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"