Okay.. I rerolled 3.3 and afterwards 3.4B6 worked...
I will test the functions.
Thanks a lot.
Good morning together..
I just got a Vivedino Trodoon 400.
It ran with Duet 2.x and I wanted to upgrade it to an actual Duet Firmware.
However.. After upgrading to 3.0 all seemed to work fine.
After upgrading to 3.3 I got the same issues as reported by Guzzi.
I should have read this topic before upgrading my system.
I am not able to downgrade the Firmware to earlier FW releases.
After uploading the Firmware the machine refuses to upgrade with error, something like that:
M997 In-application programming binary Duet2_SDiap32_WiFiEth.bin not found
Even if I manual put this file in to System it does not work.
Any tipps or workflows how to downgrade back to 3.0?
I have read different topics but it was too much input last night and I had to got to bed...
Thank a lot.
I deleted the line
M307 H3 A-1 C-1 D-1 ; reserve pin 21 for M42 or servo use
and adjusted the speed.
Now my speeds are all right.
What could be wrong if my Nozzle is too far from the Bed?
Even if I adjust my Z-Value to 0,7 it still kepps at the same distance.
G31 P45 X0 Y22 Z0.95
with a smaller Value my Z-Offset is too far from the Bed by 0,25 mm.
I dialed my Height with 520,65 as accurate as I could.
M665 R157 L397.1073 B175 H520.65
This is my actual config.g
; Configuration file for Duet WiFi (firmware version 3.3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.3.4 on Wed Oct 20 2021 13:10:50 GMT+0200 (Mitteleuropäische Sommerzeit) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Tevo LM" ; set printer name M665 R157 L397.1073 B175 H520.65 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M569 P4 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z4 E3 ; set drive mapping M350 X32 Y32 Z32 E32 I0 ; configure microstepping without interpolation M92 X160.00 Y160.00 Z160.00 E837.00 ; set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min) M201 X1500.00 Y1500.00 Z1500.00 E1000.00 ; set accelerations (mm/s^2) M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin zstop ; Z-Probe G31 P45 X0 Y22 Z0.95 ; Set Z probe trigger value, offset and trigger height (G31 P25 X0 Y0 Z1.3 ) M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch M558 P9 C"^zprobe.in" H10 F250 T1000 ; set Z probe type to bltouch and the dive height + speeds M557 R130 S20 ; Define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 ;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M307 H0 B0 R0.415 C518.9 D6.20 S1.00 V24.0 M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M307 H1 B0 R1.947 C255.7 D6.36 S1.00 V23.8 M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 C"Cold-End" S0 H T50 ; set fan 0 name and value. Thermostatic control is turned on M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 C"Partfan_links" S0 H-1 ; set fan 1 name and value. Thermostatic control is turned off M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency M106 P2 C"Partfan_rechts" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M501 ;Recall the settings ; Custom settings are not defined
And by the way...
It is really great how fast you all helped me out here.
Great Forum and great support.
I am converting my Tevo LM with a DUET 2 Wifi. I struggle a bit with the travelspeed in X/Y with G32 & G29.
I already searched for some topics but couldn´t find something that helped me.
Homing works fine. I can move all my axis with high speed. G30 is working with the BLtouch just fine.
But when I use Delta Calibration (G32) and Mesh Compensation (G29) the whole axis movements are cut down to like 10%.
Both, G32 & G29, succeed and I get the data correctly. But I would like to run it with higher X/Y-speed.
Any clue what could be wrong?
Here is my config.g
Please consider.. The Z-Output might be damaged on my board, so I mapped my Z-axis to drive 4 (E1).
M665 R157 L397.1073 B175 H515
...value 515 is a few mm shorter than my real height. If I home all and go to Z0 I am a few mm above my bed. Is this wrong?
M208 Z0 S1
I hope this is just a small thing to fix.
I have nothing declared in tfreex.g or tprex.g files.
I put in my toolchange script in tpost
; tpost0.g ; called after tool 0 has been selected ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 30 2020 18:35:35 GMT+0200 (Mitteleuropäische Sommerzeit) ; Wait for set temperatures to be reached G91 ;set to relative G1 Z5 F9999 ;move Z 5 mm up G90 ;set to absolute G1 X195 F9999 ;move quickly near switch position G1 X215 F250 ;switch to E1 G1 X195 F9999 ;move back G91 ;set to relative G1 Z-2 F9999 ;go back to initial Z-Position G90 ;set to absolute M116 P0 ;wait for extruder
; tpost1.g: ; called after tool 1 has been selected ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 30 2020 18:35:35 GMT+0200 (Mitteleuropäische Sommerzeit) ; Wait for set temperatures to be reached G91 ;set to relative G1 Z5 F9999 ;move Z 5 mm up G90 ;set to absolute G1 X0 F9999 ;move quickly near switch position G1 H1 X-14 F250 ;switch to E0 G1 X0 F9999 ;move back G91 ;set to relative G1 Z-5 F9999 ;go back to initial Z-Position G90 ;set to absolute M116 P1 ;wait for extruder